| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix optc2_configure warning on dcn314
[Why]
dcn314 uses optc2_configure_crc() that wraps
optc1_configure_crc() + set additional registers
not applicable to dcn314.
It's not critical but when used leads to warning like:
WARNING: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c
Call Trace:
<TASK>
generic_reg_set_ex+0x6d/0xe0 [amdgpu]
optc2_configure_crc+0x60/0x80 [amdgpu]
dc_stream_configure_crc+0x129/0x150 [amdgpu]
amdgpu_dm_crtc_configure_crc_source+0x5d/0xe0 [amdgpu]
[How]
Use optc1_configure_crc() directly |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Drop snd_BUG_ON() from snd_usbmidi_output_open()
snd_usbmidi_output_open() has a check of the NULL port with
snd_BUG_ON(). snd_BUG_ON() was used as this shouldn't have happened,
but in reality, the NULL port may be seen when the device gives an
invalid endpoint setup at the descriptor, hence the driver skips the
allocation. That is, the check itself is valid and snd_BUG_ON()
should be dropped from there. Otherwise it's confusing as if it were
a real bug, as recently syzbot stumbled on it. |
| In the Linux kernel, the following vulnerability has been resolved:
dm ioctl: fix misbehavior if list_versions races with module loading
__list_versions will first estimate the required space using the
"dm_target_iterate(list_version_get_needed, &needed)" call and then will
fill the space using the "dm_target_iterate(list_version_get_info,
&iter_info)" call. Each of these calls locks the targets using the
"down_read(&_lock)" and "up_read(&_lock)" calls, however between the first
and second "dm_target_iterate" there is no lock held and the target
modules can be loaded at this point, so the second "dm_target_iterate"
call may need more space than what was the first "dm_target_iterate"
returned.
The code tries to handle this overflow (see the beginning of
list_version_get_info), however this handling is incorrect.
The code sets "param->data_size = param->data_start + needed" and
"iter_info.end = (char *)vers+len" - "needed" is the size returned by the
first dm_target_iterate call; "len" is the size of the buffer allocated by
userspace.
"len" may be greater than "needed"; in this case, the code will write up
to "len" bytes into the buffer, however param->data_size is set to
"needed", so it may write data past the param->data_size value. The ioctl
interface copies only up to param->data_size into userspace, thus part of
the result will be truncated.
Fix this bug by setting "iter_info.end = (char *)vers + needed;" - this
guarantees that the second "dm_target_iterate" call will write only up to
the "needed" buffer and it will exit with "DM_BUFFER_FULL_FLAG" if it
overflows the "needed" space - in this case, userspace will allocate a
larger buffer and retry.
Note that there is also a bug in list_version_get_needed - we need to add
"strlen(tt->name) + 1" to the needed size, not "strlen(tt->name)". |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Check sb_bsize_shift after reading superblock
Fuzzers like to scribble over sb_bsize_shift but in reality it's very
unlikely that this field would be corrupted on its own. Nevertheless it
should be checked to avoid the possibility of messy mount errors due to
bad calculations. It's always a fixed value based on the block size so
we can just check that it's the expected value.
Tested with:
mkfs.gfs2 -O -p lock_nolock /dev/vdb
for i in 0 -1 64 65 32 33; do
gfs2_edit -p sb field sb_bsize_shift $i /dev/vdb
mount /dev/vdb /mnt/test && umount /mnt/test
done
Before this patch we get a withdraw after
[ 76.413681] gfs2: fsid=loop0.0: fatal: invalid metadata block
[ 76.413681] bh = 19 (type: exp=5, found=4)
[ 76.413681] function = gfs2_meta_buffer, file = fs/gfs2/meta_io.c, line = 492
and with UBSAN configured we also get complaints like
[ 76.373395] UBSAN: shift-out-of-bounds in fs/gfs2/ops_fstype.c:295:19
[ 76.373815] shift exponent 4294967287 is too large for 64-bit type 'long unsigned int'
After the patch, these complaints don't appear, mount fails immediately
and we get an explanation in dmesg. |
| In the Linux kernel, the following vulnerability has been resolved:
netlink: Bounds-check struct nlmsgerr creation
In preparation for FORTIFY_SOURCE doing bounds-check on memcpy(),
switch from __nlmsg_put to nlmsg_put(), and explain the bounds check
for dealing with the memcpy() across a composite flexible array struct.
Avoids this future run-time warning:
memcpy: detected field-spanning write (size 32) of single field "&errmsg->msg" at net/netlink/af_netlink.c:2447 (size 16) |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Prevent bpf program recursion for raw tracepoint probes
We got report from sysbot [1] about warnings that were caused by
bpf program attached to contention_begin raw tracepoint triggering
the same tracepoint by using bpf_trace_printk helper that takes
trace_printk_lock lock.
Call Trace:
<TASK>
? trace_event_raw_event_bpf_trace_printk+0x5f/0x90
bpf_trace_printk+0x2b/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
bpf_trace_printk+0x3f/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
bpf_trace_printk+0x3f/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
bpf_trace_printk+0x3f/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
__unfreeze_partials+0x5b/0x160
...
The can be reproduced by attaching bpf program as raw tracepoint on
contention_begin tracepoint. The bpf prog calls bpf_trace_printk
helper. Then by running perf bench the spin lock code is forced to
take slow path and call contention_begin tracepoint.
Fixing this by skipping execution of the bpf program if it's
already running, Using bpf prog 'active' field, which is being
currently used by trampoline programs for the same reason.
Moving bpf_prog_inc_misses_counter to syscall.c because
trampoline.c is compiled in just for CONFIG_BPF_JIT option.
[1] https://lore.kernel.org/bpf/YxhFe3EwqchC%2FfYf@krava/T/#t |
| In the Linux kernel, the following vulnerability has been resolved:
filemap: Handle sibling entries in filemap_get_read_batch()
If a read races with an invalidation followed by another read, it is
possible for a folio to be replaced with a higher-order folio. If that
happens, we'll see a sibling entry for the new folio in the next iteration
of the loop. This manifests as a NULL pointer dereference while holding
the RCU read lock.
Handle this by simply returning. The next call will find the new folio
and handle it correctly. The other ways of handling this rare race are
more complex and it's just not worth it. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_net: fix xdp_rxq_info bug after suspend/resume
The following sequence currently causes a driver bug warning
when using virtio_net:
# ip link set eth0 up
# echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem)
<resume>
# ip link set eth0 down
Missing register, driver bug
WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60
Call trace:
xdp_rxq_info_unreg+0x58/0x60
virtnet_close+0x58/0xac
__dev_close_many+0xac/0x140
__dev_change_flags+0xd8/0x210
dev_change_flags+0x24/0x64
do_setlink+0x230/0xdd0
...
This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().
Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.
Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix lockdep splat in in6_dump_addrs()
As reported by syzbot, we should not use rcu_dereference()
when rcu_read_lock() is not held.
WARNING: suspicious RCU usage
5.19.0-rc2-syzkaller #0 Not tainted
net/ipv6/addrconf.c:5175 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by syz-executor326/3617:
#0: ffffffff8d5848e8 (rtnl_mutex){+.+.}-{3:3}, at: netlink_dump+0xae/0xc20 net/netlink/af_netlink.c:2223
stack backtrace:
CPU: 0 PID: 3617 Comm: syz-executor326 Not tainted 5.19.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
in6_dump_addrs+0x12d1/0x1790 net/ipv6/addrconf.c:5175
inet6_dump_addr+0x9c1/0xb50 net/ipv6/addrconf.c:5300
netlink_dump+0x541/0xc20 net/netlink/af_netlink.c:2275
__netlink_dump_start+0x647/0x900 net/netlink/af_netlink.c:2380
netlink_dump_start include/linux/netlink.h:245 [inline]
rtnetlink_rcv_msg+0x73e/0xc90 net/core/rtnetlink.c:6046
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2501
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x917/0xe10 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2492
___sys_sendmsg+0xf3/0x170 net/socket.c:2546
__sys_sendmsg net/socket.c:2575 [inline]
__do_sys_sendmsg net/socket.c:2584 [inline]
__se_sys_sendmsg net/socket.c:2582 [inline]
__x64_sys_sendmsg+0x132/0x220 net/socket.c:2582
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix insufficient bounds propagation from adjust_scalar_min_max_vals
Kuee reported a corner case where the tnum becomes constant after the call
to __reg_bound_offset(), but the register's bounds are not, that is, its
min bounds are still not equal to the register's max bounds.
This in turn allows to leak pointers through turning a pointer register as
is into an unknown scalar via adjust_ptr_min_max_vals().
Before:
func#0 @0
0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0))
1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0))
2: (87) r3 = -r3 ; R3_w=scalar()
3: (87) r3 = -r3 ; R3_w=scalar()
4: (47) r3 |= 32767 ; R3_w=scalar(smin=-9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-2147450881)
5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
6: (95) exit
from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
8: (95) exit
from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
9: (07) r3 += -32767 ; R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)) <--- [*]
10: (95) exit
What can be seen here is that R3=scalar(umin=32767,umax=32768,var_off=(0x7fff;
0x8000)) after the operation R3 += -32767 results in a 'malformed' constant, that
is, R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)). Intersecting with var_off has
not been done at that point via __update_reg_bounds(), which would have improved
the umax to be equal to umin.
Refactor the tnum <> min/max bounds information flow into a reg_bounds_sync()
helper and use it consistently everywhere. After the fix, bounds have been
corrected to R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) and thus the register
is regarded as a 'proper' constant scalar of 0.
After:
func#0 @0
0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0))
1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0))
2: (87) r3 = -r3 ; R3_w=scalar()
3: (87) r3 = -r3 ; R3_w=scalar()
4: (47) r3 |= 32767 ; R3_w=scalar(smin=-9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-2147450881)
5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
6: (95) exit
from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767)
8: (95) exit
from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: atlantic: remove aq_nic_deinit() when resume
aq_nic_deinit() has been called while suspending, so we don't have to call
it again on resume.
Actually, call it again leads to another hang issue when resuming from
S3.
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992345] Call Trace:
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992346] <TASK>
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992348] aq_nic_deinit+0xb4/0xd0 [atlantic]
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992356] aq_pm_thaw+0x7f/0x100 [atlantic]
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992362] pci_pm_resume+0x5c/0x90
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992366] ? pci_pm_thaw+0x80/0x80
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992368] dpm_run_callback+0x4e/0x120
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992371] device_resume+0xad/0x200
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992373] async_resume+0x1e/0x40
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992374] async_run_entry_fn+0x33/0x120
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992377] process_one_work+0x220/0x3c0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992380] worker_thread+0x4d/0x3f0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992382] ? process_one_work+0x3c0/0x3c0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992384] kthread+0x12a/0x150
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992386] ? set_kthread_struct+0x40/0x40
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992387] ret_from_fork+0x22/0x30
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992391] </TASK>
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992392] ---[ end trace 1ec8c79604ed5e0d ]---
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992394] PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992397] atlantic 0000:02:00.0: PM: failed to resume async: error -110 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: sof_sdw: handle errors on card registration
If the card registration fails, typically because of deferred probes,
the device properties added for headset codecs are not removed, which
leads to kernel oopses in driver bind/unbind tests.
We already clean-up the device properties when the card is removed,
this code can be moved as a helper and called upon card registration
errors. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: rt7*-sdw: harden jack_detect_handler
Realtek headset codec drivers typically check if the card is
instantiated before proceeding with the jack detection.
The rt700, rt711 and rt711-sdca are however missing a check on the
card pointer, which can lead to NULL dereferences encountered in
driver bind/unbind tests. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250: Fix PM usage_count for console handover
When console is enabled, univ8250_console_setup() calls
serial8250_console_setup() before .dev is set to uart_port. Therefore,
it will not call pm_runtime_get_sync(). Later, when the actual driver
is going to take over univ8250_console_exit() is called. As .dev is
already set, serial8250_console_exit() makes pm_runtime_put_sync() call
with usage count being zero triggering PM usage count warning
(extra debug for univ8250_console_setup(), univ8250_console_exit(), and
serial8250_register_ports()):
[ 0.068987] univ8250_console_setup ttyS0 nodev
[ 0.499670] printk: console [ttyS0] enabled
[ 0.717955] printk: console [ttyS0] printing thread started
[ 1.960163] serial8250_register_ports assigned dev for ttyS0
[ 1.976830] printk: console [ttyS0] disabled
[ 1.976888] printk: console [ttyS0] printing thread stopped
[ 1.977073] univ8250_console_exit ttyS0 usage:0
[ 1.977075] serial8250 serial8250: Runtime PM usage count underflow!
[ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
[ 1.977812] univ8250_console_setup ttyS0 usage:2
[ 1.978167] printk: console [ttyS0] printing thread started
[ 1.978203] printk: console [ttyS0] enabled
To fix the issue, call pm_runtime_get_sync() in
serial8250_register_ports() as soon as .dev is set for an uart_port
if it has console enabled.
This problem became apparent only recently because 82586a721595 ("PM:
runtime: Avoid device usage count underflows") added the warning
printout. I confirmed this problem also occurs with v5.18 (w/o the
warning printout, obviously). |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: core: Fix boundary conditions in interpolation
The functions power_supply_temp2resist_simple and power_supply_ocv2cap_simple
handle boundary conditions incorrectly.
The change was introduced in a4585ba2050f460f749bbaf2b67bd56c41e30283
("power: supply: core: Use library interpolation").
There are two issues: First, the lines "high = i - 1" and "high = i" in ocv2cap
have the wrong order compared to temp2resist. As a consequence, ocv2cap
sets high=-1 if ocv>table[0].ocv, which causes an out-of-bounds read.
Second, the logic of temp2resist is also not correct.
Consider the case table[] = {{20, 100}, {10, 80}, {0, 60}}.
For temp=5, we expect a resistance of 70% by interpolation.
However, temp2resist sets high=low=2 and returns 60. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/speculation: Fill RSB on vmexit for IBRS
Prevent RSB underflow/poisoning attacks with RSB. While at it, add a
bunch of comments to attempt to document the current state of tribal
knowledge about RSB attacks and what exactly is being mitigated. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Use kzalloc for sev ioctl interfaces to prevent kernel data leak
For some sev ioctl interfaces, the length parameter that is passed maybe
less than or equal to SEV_FW_BLOB_MAX_SIZE, but larger than the data
that PSP firmware returns. In this case, kmalloc will allocate memory
that is the size of the input rather than the size of the data.
Since PSP firmware doesn't fully overwrite the allocated buffer, these
sev ioctl interface may return uninitialized kernel slab memory. |
| In the Linux kernel, the following vulnerability has been resolved:
md/bitmap: don't set sb values if can't pass sanity check
If bitmap area contains invalid data, kernel will crash then mdadm
triggers "Segmentation fault".
This is cluster-md speical bug. In non-clustered env, mdadm will
handle broken metadata case. In clustered array, only kernel space
handles bitmap slot info. But even this bug only happened in clustered
env, current sanity check is wrong, the code should be changed.
How to trigger: (faulty injection)
dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sda
dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sdb
mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sda /dev/sdb
mdadm -Ss
echo aaa > magic.txt
== below modifying slot 2 bitmap data ==
dd if=magic.txt of=/dev/sda seek=16384 bs=1 count=3 <== destroy magic
dd if=/dev/zero of=/dev/sda seek=16436 bs=1 count=4 <== ZERO chunksize
mdadm -A /dev/md0 /dev/sda /dev/sdb
== kernel crashes. mdadm outputs "Segmentation fault" ==
Reason of kernel crash:
In md_bitmap_read_sb (called by md_bitmap_create), bad bitmap magic didn't
block chunksize assignment, and zero value made DIV_ROUND_UP_SECTOR_T()
trigger "divide error".
Crash log:
kernel: md: md0 stopped.
kernel: md/raid1:md0: not clean -- starting background reconstruction
kernel: md/raid1:md0: active with 2 out of 2 mirrors
kernel: dlm: ... ...
kernel: md-cluster: Joined cluster 44810aba-38bb-e6b8-daca-bc97a0b254aa slot 1
kernel: md0: invalid bitmap file superblock: bad magic
kernel: md_bitmap_copy_from_slot can't get bitmap from slot 2
kernel: md-cluster: Could not gather bitmaps from slot 2
kernel: divide error: 0000 [#1] SMP NOPTI
kernel: CPU: 0 PID: 1603 Comm: mdadm Not tainted 5.14.6-1-default
kernel: Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod]
kernel: RSP: 0018:ffffc22ac0843ba0 EFLAGS: 00010246
kernel: ... ...
kernel: Call Trace:
kernel: ? dlm_lock_sync+0xd0/0xd0 [md_cluster 77fe..7a0]
kernel: md_bitmap_copy_from_slot+0x2c/0x290 [md_mod 24ea..d3a]
kernel: load_bitmaps+0xec/0x210 [md_cluster 77fe..7a0]
kernel: md_bitmap_load+0x81/0x1e0 [md_mod 24ea..d3a]
kernel: do_md_run+0x30/0x100 [md_mod 24ea..d3a]
kernel: md_ioctl+0x1290/0x15a0 [md_mod 24ea....d3a]
kernel: ? mddev_unlock+0xaa/0x130 [md_mod 24ea..d3a]
kernel: ? blkdev_ioctl+0xb1/0x2b0
kernel: block_ioctl+0x3b/0x40
kernel: __x64_sys_ioctl+0x7f/0xb0
kernel: do_syscall_64+0x59/0x80
kernel: ? exit_to_user_mode_prepare+0x1ab/0x230
kernel: ? syscall_exit_to_user_mode+0x18/0x40
kernel: ? do_syscall_64+0x69/0x80
kernel: entry_SYSCALL_64_after_hwframe+0x44/0xae
kernel: RIP: 0033:0x7f4a15fa722b
kernel: ... ...
kernel: ---[ end trace 8afa7612f559c868 ]---
kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod] |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix resource leak in lpfc_sli4_send_seq_to_ulp()
If no handler is found in lpfc_complete_unsol_iocb() to match the rctl of a
received frame, the frame is dropped and resources are leaked.
Fix by returning resources when discarding an unhandled frame type. Update
lpfc_fc_frame_check() handling of NOP basic link service. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc3-topology: Correct get_control_data for non bytes payload
It is possible to craft a topology where sof_get_control_data() would do
out of bounds access because it expects that it is only called when the
payload is bytes type.
Confusingly it also handles other types of controls, but the payload
parsing implementation is only valid for bytes.
Fix the code to count the non bytes controls and instead of storing a
pointer to sof_abi_hdr in sof_widget_data (which is only valid for bytes),
store the pointer to the data itself and add a new member to save the size
of the data.
In case of non bytes controls we store the pointer to the chanv itself,
which is just an array of values at the end.
In case of bytes control, drop the wrong cdata->data (wdata[i].pdata) check
against NULL since it is incorrect and invalid in this context.
The data is pointing to the end of cdata struct, so it should never be
null. |
