| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: fix NULL dereference in set_coalesce before first open
The Rx ring priv and index are only set in bcmgenet_init_rx_ring(),
which runs at open. Setting the Rx coalescing parameters on an interface
that was never opened, e.g. "ethtool -C eth0 rx-usecs 50", dereferences
a NULL ring->priv. The oops happens with RTNL held, so networking
stays stuck until a reboot:
Unable to handle kernel paging request at virtual address 0000000000002788
pc : bcmgenet_set_rx_coalesce.isra.0+0x10/0x88
lr : bcmgenet_set_coalesce+0xe8/0x180
Call trace:
bcmgenet_set_rx_coalesce.isra.0+0x10/0x88 (P)
__ethnl_set_coalesce.isra.0+0x490/0x570
ethnl_set_coalesce+0x48/0xc0
ethnl_default_set_doit+0xf4/0x230
genl_family_rcv_msg_doit+0xe8/0x160
genl_rcv_msg+0x220/0x2a0
netlink_rcv_skb+0x68/0x140
genl_rcv+0x40/0x60
netlink_unicast+0x338/0x3c0
netlink_sendmsg+0x19c/0x3f8
__sock_sendmsg+0x64/0xc0
__sys_sendto+0x124/0x198
__arm64_sys_sendto+0x30/0x48
Set priv and index at probe. Writing the registers while the interface
is down is harmless because open resets the MAC and
bcmgenet_init_rx_coalesce() reapplies the stored values.
It was observed on a Raspberry Pi CM4, but should apply to all other
genet devices. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: allocate dummy netdev sooner
The RX rings and the shared NAPI are carried by an internal "dummy" netdev
(eth->dummy_dev). mtk_probe() creates that dummy device, and adds the
shared tx/rx NAPI to it, only after the MAC netdevs have been registered.
That order has been there since the MT7623 support was added and leaves a
window in which the netdevs are visible to the network core before the
shared NAPI and the dummy device exist.
If anything brings the first netdev up during that window (e.g. netifd
opening the WAN link the instant the interface is registered), the
first-open path runs without them. On NETSYS v2 and later SoCs
mtk_rx_alloc() -> __xdp_rxq_info_reg() then dereferences eth->dummy_dev ==
NULL:
WARNING: CPU: ... Missing net_device from driver
in net/core/xdp.c and mtk_open() fails with -ENODEV. On NETSYS v1 SoCs
(MT7621/MT7622/MT7623/MT7629) there is no page pool, so the same open
instead calls napi_enable() on a napi_struct that netif_napi_add() has not
initialised yet and dereferences a NULL napi->dev.
Allocate the dummy netdev and add the shared tx/rx NAPI to it before the
register_netdev() loop. Both the dummy-allocation failure and a
register_netdev() failure now unwind through mtk_unreg_dev(), which
unregisters the net_device notifiers and the netdevs registered so far,
stopping a concurrently-opened netdev (ndo_stop) and its NAPI before the
dummy carrier is freed.
A netdev that opened during the window can also have queued the
frame-engine reset worker (via the tx watchdog or phylink), so the probe
error path now cancels eth->pending_work before freeing the shared state,
as mtk_cleanup() already does on remove. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: filter some flags received in the backup server
While the IPVS SYNC protocol is not secure by design
we can still protect the backup server from messages that
can wreak havoc.
This commit addresses problems from received connection flags
or their combinations. We now drop messages as follows:
1. the NO_CPORT+TEMPLATE combination allows lookups for normal
connections to hit template which can break in many ways.
While the master does not sync connections with NO_CPORT flag,
i.e. before they are established, we still accept NO_CPORT
without TEMPLATE.
2. ONE_PACKET: it is not sent by master, so we do not
expect it in backup. Before now it was ignored by
IP_VS_CONN_F_BACKUP_MASK for protocol v1 while protocol
v0 created connections that are not hashed and dropped
immediately. Better to apply the IP_VS_CONN_F_BACKUP_MASK
also to the flags from v0 messages for consistency with v1. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bpf: reject invalid NAT manipulation types
As bpf_ct_set_nat_info() is not validating the NAT manipulation type a
wrong value can be passed directly to nf_nat_setup_info(). This triggers
the WARN_ON() at nf_nat_setup_info() and if panic_on_warn isn't set,
then IPS_SRC_NAT_DONE is set without adding nat_bysource and conntrack
cleanup tries to unlink an uninitialized hlist node.
Fix this by checking that NAT manipulation type is correct before
calling nf_nat_setup_info(). In addition, if the WARN_ON is hit, return
NF_DROP instead of continuing with the processing to avoid similar
situations in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: generalize pending status bit
Rename NF_FLOW_HW_PENDING to NF_FLOW_PENDING and use it to inhibit the
flowtable GC worker until pending hw offload work has been completed.
Apparently, nf_flow_offload_stats() can schedule work to retrieve stats
while the flow is being removed by GC.
And this bit can also be used in a follow up patch to disable GC until
the flow has been fully added in both directions.
Revert the reordering done in commit d644b23afe1e ("netfilter:
flowtable: publish HW_DEAD after worker is done") to prevent a race
between GC and hw offload handler. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix race between perf_event_exit_task() and perf_pending_task()
A race condition exists between perf_event_exit_task() and
perf_pending_task() during begin_new_exec().
During begin_new_exec(), perf_event_exit_task() may be called, and the
PF_EXITING flag is not set on task. So perf_sigtrap() continues to execute
and triggers WARN_ON_ONCE(event->ctx->task != current).
Since both task exit and exec paths can call perf_event_exit_task() which
sets ctx->task to TASK_TOMBSTONE, fix this by explicitly checking if
event->ctx->task equals TASK_TOMBSTONE and dropping the redundant
PF_EXITING check. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: anx7411 - stop the IRQ before destroying the workqueue
The IRQ is devm-managed, so it can still queue plat->work while
remove() is tearing the queue down. Disable it first. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: fix saved termios reset race
Resetting saved termios state on device registration is needed where a
minor number can be reused for an entirely different device and where
the old settings may prevent the port from even being opened (e.g. when
CLOCAL is not set).
Not all TTY drivers guarantee that the minor number is no longer in use
when registering devices however, something which can lead to a
use-after-free when closing a TTY (and saving its termios) races with
re-registration.
Add a new TTY_DRIVER_RESET_SAVED_TERMIOS flag to request that any saved
termios state is reset on registration and only set it for drivers that
make sure that the minor number is no longer in use. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: max3100: shut down timer before freeing port
max3100_shutdown() stops the polling timer but returns early during
system suspend. If the SPI device is unbound before resume, the serial
core does not call max3100_shutdown() again, so max3100_remove() frees
the port while the timer remains armed. max3100_timeout() may then
access the freed port and re-arm the timer.
Add final timer teardown to max3100_remove() and use
timer_shutdown_sync() to prevent a racing callback from re-arming it.
Also free the IRQ and destroy the workqueue there before freeing the
port. Keep timer_delete_sync() in max3100_shutdown() so that a
subsequent open() can re-arm the timer.
The workqueue is created before request_irq() and destroyed on both
request_irq() failure and normal shutdown. Its presence at remove thus
identifies the IRQ left registered when suspend bypasses shutdown.
Free the IRQ before destroying the workqueue, in both
max3100_shutdown() and max3100_remove(), and cancel the pending work
in between. free_irq() waits for a running interrupt handler to
finish and no new handler can start afterwards, so a racing handler
cannot queue work on a workqueue that is being destroyed; the
force_end_work check in max3100_dowork() only narrows that window, as
a handler delayed between the check and queue_work() could still run
after the teardown has cleared the workqueue pointer. Cancelling the
work also keeps destroy_workqueue() from waiting on a queued work item
in case remove() ever runs while the freezable workqueue is still
frozen, e.g. device removal during the resume window, before
workqueues are thawed.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_bcm7271: fix use-after-free in brcmuart_remove()
brcmuart_handle_irq() starts priv->hrt to work around a receive-timeout
quirk of the 8250 core when hardware flow control is enabled; the timer
callback brcmuart_hrtimer_func() dereferences priv.
brcmuart_remove() cancels the hrtimer before it unregisters the port, so
a receive-timeout interrupt that arrives in between re-arms the timer.
After devm frees priv, the callback runs on freed memory.
Unregister the port before cancelling the hrtimer.
serial8250_unregister_port() shuts the port down and frees its IRQ, so
brcmuart_handle_irq() can no longer restart the timer, and the final
hrtimer_cancel() drains any timer that was armed before or during the
unregister.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Serialize compat port-info ioctls
The native sequencer ioctl path serializes handler calls with
client->ioctl_mutex, but the translated port-info compat path invokes the
same handlers through snd_seq_kernel_client_ctl() without taking that
mutex.
This lets concurrent compat CREATE_PORT requests pass the port-count
check before any request reaches the serialized insertion. The computed
integer port index can then exceed the address field range and wrap to an
existing index. Subsequent subscriber teardown can resolve the duplicate
address to the wrong port and access a freed subscriber.
Take ioctl_mutex while dispatching converted port-info requests, matching
the native ioctl path. All translated port-info commands share this
helper, so their accesses to the client port state are serialized as
well. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Serialize SMP remote OOB data access
build_pairing_cmd() looks up remote OOB data and copies its contents
without holding hdev->lock, which serializes the list's writers. After
SMP finds an entry, a concurrent management Remove Remote OOB Data
command can unlink and free it before SMP reads its present flag or
copies its random and confirmation values. Removal can also invalidate
an entry while the lookup is still traversing the list.
KASAN reported:
BUG: KASAN: slab-use-after-free in build_pairing_cmd+0x948/0x9b0
Call Trace:
build_pairing_cmd+0x948/0x9b0
smp_recv_cb+0x459f/0x8110
l2cap_recv_frame+0xf14/0x9190
l2cap_recv_acldata+0xa64/0xd40
hci_rx_work+0x4ca/0x730
Allocated by task 87:
hci_add_remote_oob_data+0x11d/0x530
add_remote_oob_data+0x282/0x400
hci_sock_sendmsg+0x1033/0x1ea0
Freed by task 93:
hci_remote_oob_data_clear+0x108/0x1c0
remove_remote_oob_data+0x198/0x220
hci_sock_sendmsg+0x1033/0x1ea0
Taking hdev->lock in build_pairing_cmd() would recurse for callers that
already hold it and invert the device-to-L2CAP lock order on the receive
path. Add a per-device remote_oob_lock instead, held across the SMP
lookup and copies and by the add, remove and clear helpers. Cover
initialization and in-place updates as well, so SMP cannot read partially
initialized or updated OOB values. Release the mutex on allocation
failure, preserving the existing error return.
The new critical sections acquire no device, connection or channel locks.
Writers retain their existing hdev->lock protection, which continues to
serialize the other readers without changing their locking or behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix inquiry cache use-after-free
The sync command worker holds hdev->req_lock, but inquiry-cache updates
and flushes use hdev->lock. Both hci_acl_create_conn_sync() and
hci_stop_discovery_sync() look up entries and read their fields without
taking hdev->lock.
After either lookup returns, a concurrent HCIINQUIRY ioctl can acquire
hdev->lock and flush the cache, freeing the entry. The worker then reads
the freed entry while preparing a create-connection or remote-name-cancel
command. The list traversal also races with cache updates and removal.
KASAN reported these accesses:
BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0x5f1/0x650
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_acl_create_conn_sync+0x5f1/0x650
hci_cmd_sync_work+0x13c/0x290
Allocated by task 90:
hci_inquiry_cache_update+0x3e6/0x7d0
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 93:
hci_inquiry_cache_flush+0x111/0x2b0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
BUG: KASAN: slab-use-after-free in hci_stop_discovery_sync+0x3b1/0x3c0
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_stop_discovery_sync+0x3b1/0x3c0
hci_cmd_sync_work+0x173/0x300
Allocated by task 86:
hci_inquiry_cache_update+0x483/0x940
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 91:
hci_inquiry_cache_flush+0x13e/0x2f0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
Hold hdev->lock across each lookup and all reads from its result. Copy the
remote address before unlocking so discovery cancellation does not retain
a cache entry pointer. Release the lock before sending synchronous HCI
commands, since their completion handlers may need the same lock. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize fragmented ISO packet queueing
The fragmented path in hci_queue_iso() calls __skb_queue_tail() without
holding conn->data_q.lock. The socket lock serializes senders, but the
transmit worker can concurrently remove packets from this queue using
skb_dequeue().
After an insertion saves the old tail pointer, hci_sched_iso() can dequeue
that packet and pass it to the driver. The driver can free the packet
before the insertion resumes and writes to the old tail's next pointer,
causing a use-after-free. Concurrent updates can also corrupt the queue.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_send_iso+0xc7d/0xe10
Call Trace:
hci_send_iso+0xc7d/0xe10
iso_sock_sendmsg+0x710/0x900
__sys_sendto+0x34a/0x3a0
Allocated by task 86:
__alloc_skb+0xdd/0x820
alloc_skb_with_frags+0x7e/0x770
sock_alloc_send_pskb+0x67a/0x820
bt_skb_sendmsg.constprop.0+0xc0/0x6c0
iso_sock_sendmsg+0x44e/0x900
Freed by task 90:
kmem_cache_free+0xcb/0x3d0
vhci_read+0x33f/0x4d0
vfs_read+0x177/0xa20
Hold the queue lock across the entire fragment batch, as hci_queue_acl()
does, to serialize insertion against dequeue while preserving fragment
ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cw1200: fix TX padding OOB read leaking heap data to device
The TX path rounds the transfer size up to the bus alignment
(align_size(), up to 511 bytes for SDIO, 1 byte for SPI) but sends
the padded length straight from the frame buffer, which has no room
reserved for the padding. cw1200_data_write() therefore reads past
the end of the frame and the bus transfer carries those bytes to the
device. A bogus device can collect up to 511 bytes of kernel heap
data per TX frame.
The RX path does not have this problem: it allocates the skb with
the aligned length (alloc_len) before reading.
Compute the exact padding with the bus align_size() callback, make
sure queued TX frames have tailroom for it, and zero the padding
bytes before the transfer so nothing past the frame is exposed.
This is not expected to change driver behavior on most cases: frame
contents and transfer sizes are unchanged, only the content of the
padding bytes (previously undefined stale memory, now zero), which
the device never reads since the WSM header carries the real frame
length. The skb expansion can only fail under memory exhaustion,
in which case the frame is dropped like on the existing error paths
of cw1200_tx().
Discovered by Atuin - Automated Vulnerability Discovery Engine. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: keep paired old chanctx alive
An in-place replacement keeps reciprocal replace_ctx pointers between
the old WILL_BE_REPLACED chanctx and the new REPLACES_OTHER chanctx.
However, the early free paths only consider assigned and reserved link
users when deciding whether to free the old chanctx.
That lets the old chanctx be freed too early while the replacement
partner still points back to it, either when the last assigned link is
released or when that link successfully reassigns to another existing
context. Later unreserve and switch-finalization paths can then follow a
stale replace_ctx pointer.
Keep a paired old chanctx alive until the replacement pair has been torn
down. Apply the same check to both __ieee80211_link_release_channel()
and ieee80211_link_use_reserved_reassign(). If the replacement is later
abandoned, ieee80211_link_unreserve_chanctx() already tears down the
pairing before freeing the old chanctx once no users remain. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix driver deregistration order
USB serial driver modules register one driver for the USB bus and one or
more drivers for the ports on the USB serial bus.
When unloading a driver module, the USB driver must be deregistered
before the USB serial bus drivers so that I/O is stopped before
unbinding the ports to avoid use-after-free in completion handlers
accessing port data.
Note that the "new_id" attributes must first be removed to prevent new
ids from being added and triggering a probe of the USB driver after it
has been deregistered. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: gp2ap020a00f: drain irq_work after free_irq
The threaded IRQ handler queues data->work through irq_work_queue() so
the trigger is polled from a per-CPU context. free_irq() does not flush
an irq_work the handler already queued, so after gp2ap020a00f_remove()
returns that work may still run and call iio_trigger_poll() on data->trig,
which the devm cleanup has already freed, causing a use-after-free.
Add irq_work_sync(&data->work) after free_irq() in remove() and in the
probe error path, mirroring commit 78601726d4a5 ("iio: trigger: sysfs:
fix use-after-free on remove").
Found by an in-house static analysis tool, confirmed by manual review. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: prevent collapsing skbs across boundary in rtx queue
tcp_write_collapse_fence() sets TCP_SKB_CB(skb)->eor = 1 on
tcp_write_queue_tail(sk) to prevent skbs queued after a switch to
device encryption from being collapsed into earlier skbs.
The fence is a no-op if all earlier data has already been transmitted
when the switch happens: sk->sk_write_queue is empty. The not yet
acknowledged earlier skbs wait in sk->tcp_rtx_queue with eor 0.
On a subsequent retransmit or SACK shift, tcp_retrans_try_collapse() or
tcp_shift_skb_data() can then merge an skb queued after the switch into
one queued before it.
Both users of the fence are affected:
- psp: devices only encrypt skbs with skb->decrypted set. The merged skb
keeps decrypted = 0 from the earlier skb, so merged data sent after
psp_sock_assoc_set_tx() is retransmitted in cleartext.
- tls device offload: the merged skb straddles the start marker set in
tls_set_device_offload(). The software fallback (fill_sg_in() returns
-EINVAL) and the mlx5, nfp and funeth drivers cannot handle such an
skb and drop it. Every retransmit rebuilds the same skb, so the
connection stalls.
Fix this in two places, for defense in depth:
1. Fall back to tcp_rtx_queue_tail(sk) in tcp_write_collapse_fence()
when tcp_write_queue_tail(sk) is NULL.
2. Check !skb_cmp_decrypted(to, from) in tcp_skb_can_collapse(), as
tcp_skb_can_collapse_rx() does on receive. skb_shift(), which both
collapse paths call, already has a DEBUG_NET_WARN_ON_ONCE() for this
condition. |
| In the Linux kernel, the following vulnerability has been resolved:
bna: prevent IOC timer rearm during teardown
bna: prevent IOC timer rearm during teardown
bnad_pci_remove() and the probe disable_ioceth path call
timer_delete_sync() for ioc_timer, sem_timer and hb_timer, but not for
iocpf_timer. bnad_iocpf_timeout() then takes bnad->bna_lock after
free_netdev() has freed the struct bnad.
Deleting iocpf_timer last does not fix this. sem_timer and
iocpf_timer rearm each other: bnad_iocpf_sem_timeout() can arm
iocpf_timer, and bnad_iocpf_timeout() arms sem_timer from
bfa_ioc_hw_sem_get() when the semaphore is busy.
timer_delete_sync() only waits out its own callback.
bnad_ioceth_disable() can time out and leave that callback live.
Shut all four IOC timers down with timer_shutdown_sync() on both
paths, so a later mod_timer() is ignored.
This issue was identified during our ongoing static-analysis research
while reviewing kernel code. |
