| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic: Check the interrupt is still ours before migrating it
vgic_prune_ap_list() drops both ap_list_lock and irq_lock while migrating
an interrupt to another vCPU. After reacquiring the locks it only checks
that the affinity is unchanged (target_vcpu == vgic_target_oracle(irq))
before moving the interrupt, which assumes that an interrupt whose affinity
is preserved is still queued on this vCPU's ap_list.
That assumption no longer holds if the interrupt is taken off the ap_list
while the locks are dropped. vgic_flush_pending_lpis() removes the
interrupt from the list and sets irq->vcpu to NULL, but leaves
enabled/pending/target_vcpu untouched. As the interrupt is still enabled
and pending, vgic_target_oracle() returns the same target_vcpu, so the
affinity check passes and list_del() is run a second time on an entry that
has already been removed.
Also check that the interrupt is still assigned to this vCPU
(irq->vcpu == vcpu) before moving it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sungem: fix probe error cleanup
gem_init_one() calls gem_remove_one() when register_netdev() fails.
gem_remove_one() unregisters and frees resources owned by the net_device,
including the DMA block, MMIO mapping, PCI regions, and the net_device
itself. gem_init_one() then falls through to its own cleanup labels and
frees the same resources again.
Keep the register_netdev() error path in gem_init_one(): clear drvdata so
PM/remove paths do not see a half-registered device, remove the NAPI
instance added during probe, and let the existing cleanup labels release
the resources once.
The issue was found by a local static-analysis checker for probe error
paths. The reported path was manually inspected before sending this fix.
Compile-tested with CONFIG_SUNGEM=y. Runtime testing was not performed
because no sungem hardware is available. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ump: fix double free of out_cvts on rawmidi error
snd_ump_attach_legacy_rawmidi() allocates the legacy conversion array
ump->out_cvts and, on the snd_rawmidi_new() error path, frees it with
kfree() but leaves ump->out_cvts pointing at the freed memory. When the
endpoint is later torn down, snd_ump_endpoint_free() frees ump->out_cvts
a second time, resulting in a double free.
The host snd-usb-audio driver attaches the legacy rawmidi for any USB
MIDI 2.0 (UMP) device, so a device that makes snd_rawmidi_new() fail
reaches this path on enumeration.
Clear ump->out_cvts after freeing it on the error path so it is not
freed again during teardown.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/hw_engine: Fix double-free of managed BO in error path
The error path in hw_engine_init() explicitly frees a BO allocated
with xe_managed_bo_create_pin_map() via xe_bo_unpin_map_no_vm().
Since the managed BO already has a devm cleanup action registered,
this causes a double-free when devm unwinds during probe failure.
Remove the explicit free and let devm handle it, consistent with
all other xe_managed_bo_create_pin_map() callers.
(cherry picked from commit e459a3bdeb117be496d7f229e2ea1f6c9fe4080b) |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: harden rq_procinfo lifecycle to prevent double-free
The svc_release_rqst() function executes the callback inside
rqstp->rq_procinfo->pc_release. However, if a worker thread begins
processing a new request and encounters an early error path (e.g.,
unsupported protocol, short frame, or bad auth) before a valid
rq_procinfo is installed, a stale release hook can be re-triggered
against reused state from the previous RPC, resulting in a double-free
or use-after-free vulnerability.
Harden the lifecycle of rq_procinfo by:
1. Ensuring svc_release_rqst() always clears rq_procinfo after the
optional pc_release() call, regardless of whether the hook exists.
2. Explicitly clearing rq_procinfo at request entry in svc_process()
before any early decode or drop paths.
3. Ensuring svc_process_bc() does the same at backchannel entry.
This guarantees that error flows will not encounter a non-NULL stale
rq_procinfo pointer when there is nothing to release. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Don't move a peeked OOB message onto the pending queue
rxrpc_recvmsg_oob() takes a received oob message off recvmsg_oobq and,
if a response is needed, moves it onto the pending_oobq tree. However,
only the unlink from recvmsg_oobq is guarded by MSG_PEEK; the move onto
pending_oobq always runs.
As a result, reading a challenge with MSG_PEEK leaves the skb on
recvmsg_oobq while also adding it to pending_oobq. Since struct
sk_buff's rbnode shares storage with its next and prev pointers,
rb_insert_color() overwrites the list linkage, and the skb, which holds
a single reference, becomes reachable from both queues at once.
When the socket is closed both queues are drained in turn. While
draining recvmsg_oobq, __skb_unlink() follows the next and prev
pointers that rbnode has overwritten and writes to a bad address. Also,
as the skb holds a single reference but is freed from each queue, both
the skb and the connection reference it holds are released twice. This
leads to memory corruption and to a use-after-free caused by the
connection refcount underflow.
MSG_PEEK does not consume the message from the queue, so only unlink it
from recvmsg_oobq and then move it onto pending_oobq or free it when
the message is actually consumed. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: nat_keepalive: avoid double free on send error
nat_keepalive_send() frees the keepalive skb whenever the IPv4 or IPv6
send helper reports an error.
That cleanup is only correct before the skb is handed to the output
path. Once ip_build_and_send_pkt() or ip6_xmit() takes ownership, the
networking stack may already have consumed the skb before returning an
error, so freeing it again is unsafe.
Handle the pre-handoff failure cases inside nat_keepalive_send_ipv4()
and nat_keepalive_send_ipv6(), where the caller still owns the skb, and
keep nat_keepalive_send() responsible only for family dispatch and the
unsupported-family cleanup path. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: most: video: avoid double free on video register failure
comp_register_videodev() allocates a video_device with
video_device_alloc() and releases it if video_register_device() fails.
This can double free the video_device when __video_register_device()
reaches device_register() and that call fails:
video_register_device()
-> __video_register_device()
-> device_register() fails
-> put_device(&vdev->dev)
-> v4l2_device_release()
-> vdev->release(vdev)
-> video_device_release(vdev)
comp_register_videodev()
-> video_device_release(mdev->vdev)
Use video_device_release_empty() while registering the device so that
registration failure paths do not free mdev->vdev through vdev->release().
comp_register_videodev() then releases mdev->vdev exactly once on failure.
Restore video_device_release() after successful registration so the
registered device keeps its normal lifetime handling.
This issue was found by a static analysis tool I am developing. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: dma-axi-dmac: Properly free struct axi_dmac_desc
Use axi_dmac_free_desc() to free fully the descriptor at fail path when
call axi_dmac_alloc_desc() in axi_dmac_prep_peripheral_dma_vec(). |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-ep-msi: Fix error unwind and prevent double alloc
pci_epf_alloc_doorbell() stores the allocated doorbell message array in
epf->db_msg/epf->num_db before requesting MSI vectors. If MSI allocation
fails, the array is freed but the EPF state may still point to freed
memory.
Clear epf->db_msg and epf->num_db on the MSI allocation failure path so
that later cleanup cannot double-free the array and callers can retry
allocation.
Also return -EBUSY when doorbells have already been allocated to prevent
leaking or overwriting an existing allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: net2280: Fix double free in probe error path
usb_initialize_gadget() installs gadget_release() as the release
callback for the embedded gadget device. The struct net2280 instance is
therefore released through gadget_release() when the gadget device's last
reference is dropped.
The probe error path calls net2280_remove(), which tears down the
partially initialized device and drops the gadget reference with
usb_put_gadget(). Calling kfree(dev) afterwards can free the same object
again.
Drop the explicit kfree() and let the gadget device release callback
handle the final free. This issue was found by a static analysis tool
I am developing. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Do not call map->ops->elt_free() if elt_alloc() fails
In paths where tracing_map_elt_alloc() failed to allocate objects,
the map->ops->elt_alloc() call was never successful. In this case,
map->ops->elt_free() should not be called. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: fix double free and WARN_ON in add_mtd_device() error paths
When device_register() or mtd_nvmem_add() fails inside
add_mtd_device() for a partition, the error handling triggers
mtd_release() via put_device() or device_unregister(). mtd_release()
calls release_mtd_partition() which frees the mtd_info structure.
However, callers such as mtd_add_partition() and add_mtd_partitions()
also call free_partition() in their error paths, resulting in a double
free.
Additionally, release_mtd_partition() hits WARN_ON(!list_empty(
&mtd->part.node)) because the partition node is still linked in the
parent's partitions list when the release callback fires from the
add_mtd_device() error path.
Fix this by overriding dev->type and dev->release before put_device()
in the error paths, so that device_release() invokes a no-op function
instead of mtd_release(). For the mtd_nvmem_add() failure case,
device_unregister() is replaced with device_del() to separate the
device removal from the final kobject reference drop, allowing the
override to take effect before put_device() is called.
The callers' error paths (list_del + free_partition) remain the sole
owners of mtd_info lifetime on add_mtd_device() failure, which is the
expected contract.
The normal partition teardown path is not affected: del_mtd_device()
goes through kref_put() -> mtd_device_release() -> device_unregister()
with dev->type still set to &mtd_devtype, so mtd_release() ->
release_mtd_partition() continues to work correctly for the regular
removal case. |
| Calling wordexp with WRDE_APPEND in the GNU C Library version 2.0 to version 2.43 can cause the interface to return invalid memory in the we_wordv member, which on subsequent calls to wordfree may abort the process. |
| Redis before 8.8.0, in the unusual case where an authenticated attacker can execute RESTORE, allows remote code execution via a RESTORE payload where the same NACK (pending entry) is referenced by more than one consumer, because deleting both consumers via XGROUP DELCONSUMER leads to a double free. NOTE: this issue exists because of an incomplete fix for CVE-2026-25243. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix double DMA unmapping for XDP_REDIRECT
Remove the dma_unmap_page_attrs() call in the driver's XDP_REDIRECT
code path. This should have been removed when we let the page pool
handle the DMA mapping. This bug causes the warning:
WARNING: CPU: 7 PID: 59 at drivers/iommu/dma-iommu.c:1198 iommu_dma_unmap_page+0xd5/0x100
CPU: 7 PID: 59 Comm: ksoftirqd/7 Tainted: G W 6.8.0-1010-gcp #11-Ubuntu
Hardware name: Dell Inc. PowerEdge R7525/0PYVT1, BIOS 2.15.2 04/02/2024
RIP: 0010:iommu_dma_unmap_page+0xd5/0x100
Code: 89 ee 48 89 df e8 cb f2 69 ff 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9 31 f6 31 ff 45 31 c0 e9 ab 17 71 00 <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9
RSP: 0018:ffffab1fc0597a48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff99ff838280c8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffab1fc0597a78 R08: 0000000000000002 R09: ffffab1fc0597c1c
R10: ffffab1fc0597cd3 R11: ffff99ffe375acd8 R12: 00000000e65b9000
R13: 0000000000000050 R14: 0000000000001000 R15: 0000000000000002
FS: 0000000000000000(0000) GS:ffff9a06efb80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000565c34c37210 CR3: 00000005c7e3e000 CR4: 0000000000350ef0
? show_regs+0x6d/0x80
? __warn+0x89/0x150
? iommu_dma_unmap_page+0xd5/0x100
? report_bug+0x16a/0x190
? handle_bug+0x51/0xa0
? exc_invalid_op+0x18/0x80
? iommu_dma_unmap_page+0xd5/0x100
? iommu_dma_unmap_page+0x35/0x100
dma_unmap_page_attrs+0x55/0x220
? bpf_prog_4d7e87c0d30db711_xdp_dispatcher+0x64/0x9f
bnxt_rx_xdp+0x237/0x520 [bnxt_en]
bnxt_rx_pkt+0x640/0xdd0 [bnxt_en]
__bnxt_poll_work+0x1a1/0x3d0 [bnxt_en]
bnxt_poll+0xaa/0x1e0 [bnxt_en]
__napi_poll+0x33/0x1e0
net_rx_action+0x18a/0x2f0 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/gsc: Fix double-free of managed BO in error path
The error path in xe_gsc_init_post_hwconfig() explicitly frees a BO
allocated with xe_managed_bo_create_pin_map() via
xe_bo_unpin_map_no_vm(). Since the managed BO already has a devm
cleanup action registered, this causes a double-free when devm
unwinds during probe failure.
Remove the explicit free and let devm handle it, consistent with
all other xe_managed_bo_create_pin_map() callers.
(cherry picked from commit 71d61e3e299a17139e47f980a4d6f425b2c59bf7) |
| Object lifecycle issue in WebRTC in Google Chrome prior to 151.0.7922.72 allowed a remote attacker to potentially exploit heap corruption via a crafted HTML page. (Chromium security severity: Medium) |
| libssh2 through 1.11.1, fixed in commit 5e47761, contains a double-free vulnerability in the sftp_open() function in src/sftp.c that allows a malicious SSH server to corrupt the heap of any authenticated client opening an SFTP session. When a server responds to SSH_FXP_OPEN with SSH_FXP_STATUS containing FX_OK, the response data buffer is freed, and if a subsequent sftp_packet_require() call returns a specific error such as LIBSSH2_ERROR_CHANNEL_PACKET_EXCEEDED, the same pointer is freed a second time, enabling tcache dup conditions on glibc systems that allow overlapping allocations and function pointer overwrites. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: reset runtime state when cloning SAs
iptfs_clone_state() clones the IPTFS mode data with kmemdup(). This
copies runtime objects which must not be shared with the original SA,
including the embedded sk_buff_head, hrtimers, spinlock, and in-flight
reassembly/reorder state.
If xfrm_state_migrate() fails after clone_state() but before the later
init_state() call has reinitialized those fields, the cloned state can be
destroyed by xfrm_state_gc_task() with list and timer state copied from the
original SA. With queued packets this lets the clone splice and free skbs
owned by the original IPTFS queue, leading to use-after-free and
double-free reports in iptfs_destroy_state() and skb release paths.
Reinitialize the clone's runtime state before publishing it through
x->mode_data. Because clone_state() now publishes a destroyable mode_data
object before init_state(), take the mode callback module reference there.
Avoid taking it again from __iptfs_init_state() for the same object. |
