| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: use list_del_rcu for netlink hooks
nft_netdev_unregister_hooks and __nft_unregister_flowtable_net_hooks need
to use list_del_rcu(), this list can be walked by concurrent dumpers.
Add a new helper and use it consistently. |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: tmc-etr: Fix race condition between sysfs and perf mode
When trying to run perf and sysfs mode simultaneously, the WARN_ON()
in tmc_etr_enable_hw() is triggered sometimes:
WARNING: CPU: 42 PID: 3911571 at drivers/hwtracing/coresight/coresight-tmc-etr.c:1060 tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc]
[..snip..]
Call trace:
tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc] (P)
tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc] (L)
tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc]
coresight_enable_path+0x1c8/0x218 [coresight]
coresight_enable_sysfs+0xa4/0x228 [coresight]
enable_source_store+0x58/0xa8 [coresight]
dev_attr_store+0x20/0x40
sysfs_kf_write+0x4c/0x68
kernfs_fop_write_iter+0x120/0x1b8
vfs_write+0x2c8/0x388
ksys_write+0x74/0x108
__arm64_sys_write+0x24/0x38
el0_svc_common.constprop.0+0x64/0x148
do_el0_svc+0x24/0x38
el0_svc+0x3c/0x130
el0t_64_sync_handler+0xc8/0xd0
el0t_64_sync+0x1ac/0x1b0
---[ end trace 0000000000000000 ]---
Since the enablement of sysfs mode is separeted into two critical regions,
one for sysfs buffer allocation and another for hardware enablement, it's
possible to race with the perf mode. Fix this by double check whether
the perf mode's been used before enabling the hardware in sysfs mode.
mode:
[sysfs mode] [perf mode]
tmc_etr_get_sysfs_buffer()
spin_lock(&drvdata->spinlock)
[sysfs buffer allocation]
spin_unlock(&drvdata->spinlock)
spin_lock(&drvdata->spinlock)
tmc_etr_enable_hw()
drvdata->etr_buf = etr_perf->etr_buf
spin_unlock(&drvdata->spinlock)
spin_lock(&drvdata->spinlock)
tmc_etr_enable_hw()
WARN_ON(drvdata->etr_buf) // WARN sicne etr_buf initialized at
the perf side
spin_unlock(&drvdata->spinlock)
With this fix, we retain the check for CS_MODE_PERF in get_etr_sysfs_buf.
This ensures we verify whether the perf mode's already running before we
actually allocate the buffer. Then we can save the time of
allocating/freeing the sysfs buffer if race with the perf mode. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: oss: Fix data race at accessing runtime.oss.trigger
Currently the runtime.oss.trigger field may be accessed concurrently
without protection, which may lead to the data race. And, in this
case, it may lead to more severe problem because it's a bit field; as
writing the data, it may overwrite other bit fields as well, which
confuses the operation completely, as spotted by fuzzing.
Fix it by covering runtime.oss.trigger bit fled also with the existing
params_lock mutex in both snd_pcm_oss_get_trigger() and
snd_pcm_oss_poll(). |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/core: fix damos_walk() vs kdamond_fn() exit race
When kdamond_fn() main loop is finished, the function cancels remaining
damos_walk() request and unset the damon_ctx->kdamond so that API callers
and API functions themselves can show the context is terminated.
damos_walk() adds the caller's request to the queue first. After that, it
shows if the kdamond of the damon_ctx is still running (damon_ctx->kdamond
is set). Only if the kdamond is running, damos_walk() starts waiting for
the kdamond's handling of the newly added request.
The damos_walk() requests registration and damon_ctx->kdamond unset are
protected by different mutexes, though. Hence, damos_walk() could race
with damon_ctx->kdamond unset, and result in deadlocks.
For example, let's suppose kdamond successfully finished the damow_walk()
request cancelling. Right after that, damos_walk() is called for the
context. It registers the new request, and shows the context is still
running, because damon_ctx->kdamond unset is not yet done. Hence the
damos_walk() caller starts waiting for the handling of the request.
However, the kdamond is already on the termination steps, so it never
handles the new request. As a result, the damos_walk() caller thread
infinitely waits.
Fix this by introducing another damon_ctx field, namely
walk_control_obsolete. It is protected by the
damon_ctx->walk_control_lock, which protects damos_walk() request
registration. Initialize (unset) it in kdamond_fn() before letting
damon_start() returns and set it just before the cancelling of the
remaining damos_walk() request is executed. damos_walk() reads the
obsolete field under the lock and avoids adding a new request.
After this change, only requests that are guaranteed to be handled or
cancelled are registered. Hence the after-registration DAMON context
termination check is no longer needed. Remove it together.
The issue is found by sashiko [1]. |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: core - use RCU and work_struct to fix race condition
Currently, hwrng_fill is not cleared until the hwrng_fillfn() thread
exits. Since hwrng_unregister() reads hwrng_fill outside the rng_mutex
lock, a concurrent hwrng_unregister() may call kthread_stop() again on
the same task.
Additionally, if hwrng_unregister() is called immediately after
hwrng_register(), the stopped thread may have never been executed. Thus,
hwrng_fill remains dirty even after hwrng_unregister() returns. In this
case, subsequent calls to hwrng_register() will fail to start new
threads, and hwrng_unregister() will call kthread_stop() on the same
freed task. In both cases, a use-after-free occurs:
refcount_t: addition on 0; use-after-free.
WARNING: ... at lib/refcount.c:25 refcount_warn_saturate+0xec/0x1c0
Call Trace:
kthread_stop+0x181/0x360
hwrng_unregister+0x288/0x380
virtrng_remove+0xe3/0x200
This patch fixes the race by protecting the global hwrng_fill pointer
inside the rng_mutex lock, so that hwrng_fillfn() thread is stopped only
once, and calls to kthread_run() and kthread_stop() are serialized
with the lock held.
To avoid deadlock in hwrng_fillfn() while being stopped with the lock
held, we convert current_rng to RCU, so that get_current_rng() can read
current_rng without holding the lock. To remove the lock from put_rng(),
we also delay the actual cleanup into a work_struct.
Since get_current_rng() no longer returns ERR_PTR values, the IS_ERR()
checks are removed from its callers.
With hwrng_fill protected by the rng_mutex lock, hwrng_fillfn() can no
longer clear hwrng_fill itself. Therefore, if hwrng_fillfn() returns
directly after current_rng is dropped, kthread_stop() would be called on
a freed task_struct later. To fix this, hwrng_fillfn() calls schedule()
now to keep the task alive until being stopped. The kthread_stop() call
is also moved from hwrng_unregister() to drop_current_rng(), ensuring
kthread_stop() is called on all possible paths where current_rng becomes
NULL, so that the thread would not wait forever. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down PASID entry
The Intel VT-d Scalable Mode PASID table entry consists of 512 bits (64
bytes). When tearing down an entry, the current implementation zeros the
entire 64-byte structure immediately using multiple 64-bit writes.
Since the IOMMU hardware may fetch these 64 bytes using multiple
internal transactions (e.g., four 128-bit bursts), updating or zeroing
the entire entry while it is active (P=1) risks a "torn" read. If a
hardware fetch occurs simultaneously with the CPU zeroing the entry, the
hardware could observe an inconsistent state, leading to unpredictable
behavior or spurious faults.
Follow the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the PASID entry.
2. Use a dma_wmb() to ensure the cleared bit is visible to hardware
before proceeding.
3. Execute the required invalidation sequence (PASID cache, IOTLB, and
Device-TLB flush) to ensure the hardware has released all cached
references.
4. Only after the flushes are complete, zero out the remaining fields
of the PASID entry.
Also, add a dma_wmb() in pasid_set_present() to ensure that all other
fields of the PASID entry are visible to the hardware before the Present
bit is set. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: mipi-i3c-hci: Fix race in DMA ring dequeue
The HCI DMA dequeue path (hci_dma_dequeue_xfer()) may be invoked for
multiple transfers that timeout around the same time. However, the
function is not serialized and can race with itself.
When a timeout occurs, hci_dma_dequeue_xfer() stops the ring, processes
incomplete transfers, and then restarts the ring. If another timeout
triggers a parallel call into the same function, the two instances may
interfere with each other - stopping or restarting the ring at unexpected
times.
Add a mutex so that hci_dma_dequeue_xfer() is serialized with respect to
itself. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: defer eventfd signaling when queued from a wakeup handler
io_req_local_work_add() signals the CQ ring eventfd inline when it is the
one to push the first entry onto ->work_list. For DEFER_TASKRUN rings that
add is frequently done from a waitqueue wakeup handler, where an
arbitrary waitqueue lock is held.
eventfd_signal_mask() only refuses to recurse when current->in_eventfd
is set, but that bit is set by eventfd_signal_mask() itself. If the wake
chain starts somewhere else, signal goes out inline and can feed back
into epoll.
Add IOU_F_TWQ_IN_WAKE, set it on the task_work add done from the three
waitqueue callbacks, and use it to force io_eventfd_signal() down the
existing call_rcu_hurry() deferral instead of signaling inline. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by
replacing mlx5_query_mac_address() with ether_addr_copy() to get the
local MAC address directly from netdev->dev_addr.
The issue occurs because mlx5_query_mac_address() queries the hardware
which involves mlx5_cmd_exec() that can sleep, but it is called from
the mlx5e_ipsec_handle_event workqueue which runs in atomic context.
The MAC address is already available in netdev->dev_addr, so no need
to query hardware. This avoids the sleeping call and resolves the bug.
Call trace:
BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200
__schedule+0x7ab/0xa20
schedule+0x1c/0xb0
schedule_timeout+0x6e/0xf0
__wait_for_common+0x91/0x1b0
cmd_exec+0xa85/0xff0 [mlx5_core]
mlx5_cmd_exec+0x1f/0x50 [mlx5_core]
mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core]
mlx5_query_mac_address+0x19/0x30 [mlx5_core]
mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core]
mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core]
mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core]
process_one_work+0x178/0x2e0
worker_thread+0x2ea/0x430 |
| In the Linux kernel, the following vulnerability has been resolved:
mpls: add seqcount to protect the platform_label{,s} pair
The RCU-protected codepaths (mpls_forward, mpls_dump_routes) can have
an inconsistent view of platform_labels vs platform_label in case of a
concurrent resize (resize_platform_label_table, under
platform_mutex). This can lead to OOB accesses.
This patch adds a seqcount, so that we get a consistent snapshot.
Note that mpls_label_ok is also susceptible to this, so the check
against RTA_DST in rtm_to_route_config, done outside platform_mutex,
is not sufficient. This value gets passed to mpls_label_ok once more
in both mpls_route_add and mpls_route_del, so there is no issue, but
that additional check must not be removed. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: tegra210-quad: Protect curr_xfer check in IRQ handler
Now that all other accesses to curr_xfer are done under the lock,
protect the curr_xfer NULL check in tegra_qspi_isr_thread() with the
spinlock. Without this protection, the following race can occur:
CPU0 (ISR thread) CPU1 (timeout path)
---------------- -------------------
if (!tqspi->curr_xfer)
// sees non-NULL
spin_lock()
tqspi->curr_xfer = NULL
spin_unlock()
handle_*_xfer()
spin_lock()
t = tqspi->curr_xfer // NULL!
... t->len ... // NULL dereference!
With this patch, all curr_xfer accesses are now properly synchronized.
Although all accesses to curr_xfer are done under the lock, in
tegra_qspi_isr_thread() it checks for NULL, releases the lock and
reacquires it later in handle_cpu_based_xfer()/handle_dma_based_xfer().
There is a potential for an update in between, which could cause a NULL
pointer dereference.
To handle this, add a NULL check inside the handlers after acquiring
the lock. This ensures that if the timeout path has already cleared
curr_xfer, the handler will safely return without dereferencing the
NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
md: suspend array while updating raid_disks via sysfs
In raid1_reshape(), freeze_array() is called before modifying the r1bio
memory pool (conf->r1bio_pool) and conf->raid_disks, and
unfreeze_array() is called after the update is completed.
However, freeze_array() only waits until nr_sync_pending and
(nr_pending - nr_queued) of all buckets reaches zero. When an I/O error
occurs, nr_queued is increased and the corresponding r1bio is queued to
either retry_list or bio_end_io_list. As a result, freeze_array() may
unblock before these r1bios are released.
This can lead to a situation where conf->raid_disks and the mempool have
already been updated while queued r1bios, allocated with the old
raid_disks value, are later released. Consequently, free_r1bio() may
access memory out of bounds in put_all_bios() and release r1bios of the
wrong size to the new mempool, potentially causing issues with the
mempool as well.
Since only normal I/O might increase nr_queued while an I/O error occurs,
suspending the array avoids this issue.
Note: Updating raid_disks via ioctl SET_ARRAY_INFO already suspends
the array. Therefore, we suspend the array when updating raid_disks
via sysfs to avoid this issue too. |
| In the Linux kernel, the following vulnerability has been resolved:
functionfs: fix the open/removal races
ffs_epfile_open() can race with removal, ending up with file->private_data
pointing to freed object.
There is a total count of opened files on functionfs (both ep0 and
dynamic ones) and when it hits zero, dynamic files get removed.
Unfortunately, that removal can happen while another thread is
in ffs_epfile_open(), but has not incremented the count yet.
In that case open will succeed, leaving us with UAF on any subsequent
read() or write().
The root cause is that ffs->opened is misused; atomic_dec_and_test() vs.
atomic_add_return() is not a good idea, when object remains visible all
along.
To untangle that
* serialize openers on ffs->mutex (both for ep0 and for dynamic files)
* have dynamic ones use atomic_inc_not_zero() and fail if we had
zero ->opened; in that case the file we are opening is doomed.
* have the inodes of dynamic files marked on removal (from the
callback of simple_recursive_removal()) - clear ->i_private there.
* have open of dynamic ones verify they hadn't been already removed,
along with checking that state is FFS_ACTIVE. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix race condition validating r_parent before applying state
Add validation to ensure the cached parent directory inode matches the
directory info in MDS replies. This prevents client-side race conditions
where concurrent operations (e.g. rename) cause r_parent to become stale
between request initiation and reply processing, which could lead to
applying state changes to incorrect directory inodes.
[ idryomov: folded a kerneldoc fixup and a follow-up fix from Alex to
move CEPH_CAP_PIN reference when r_parent is updated:
When the parent directory lock is not held, req->r_parent can become
stale and is updated to point to the correct inode. However, the
associated CEPH_CAP_PIN reference was not being adjusted. The
CEPH_CAP_PIN is a reference on an inode that is tracked for
accounting purposes. Moving this pin is important to keep the
accounting balanced. When the pin was not moved from the old parent
to the new one, it created two problems: The reference on the old,
stale parent was never released, causing a reference leak.
A reference for the new parent was never acquired, creating the risk
of a reference underflow later in ceph_mdsc_release_request(). This
patch corrects the logic by releasing the pin from the old parent and
acquiring it for the new parent when r_parent is switched. This
ensures reference accounting stays balanced. ] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/smaps: fix race between smaps_hugetlb_range and migration
smaps_hugetlb_range() handles the pte without holdling ptl, and may be
concurrenct with migration, leaing to BUG_ON in pfn_swap_entry_to_page().
The race is as follows.
smaps_hugetlb_range migrate_pages
huge_ptep_get
remove_migration_ptes
folio_unlock
pfn_swap_entry_folio
BUG_ON
To fix it, hold ptl lock in smaps_hugetlb_range(). |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: fix race between io_uring_cmd_complete_in_task and ublk_cancel_cmd
ublk_cancel_cmd() calls io_uring_cmd_done() to complete uring_cmd, but
we may have scheduled task work via io_uring_cmd_complete_in_task() for
dispatching request, then kernel crash can be triggered.
Fix it by not trying to canceling the command if ublk block request is
started. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: quota: fix to avoid warning in dquot_writeback_dquots()
F2FS-fs (dm-59): checkpoint=enable has some unwritten data.
------------[ cut here ]------------
WARNING: CPU: 6 PID: 8013 at fs/quota/dquot.c:691 dquot_writeback_dquots+0x2fc/0x308
pc : dquot_writeback_dquots+0x2fc/0x308
lr : f2fs_quota_sync+0xcc/0x1c4
Call trace:
dquot_writeback_dquots+0x2fc/0x308
f2fs_quota_sync+0xcc/0x1c4
f2fs_write_checkpoint+0x3d4/0x9b0
f2fs_issue_checkpoint+0x1bc/0x2c0
f2fs_sync_fs+0x54/0x150
f2fs_do_sync_file+0x2f8/0x814
__f2fs_ioctl+0x1960/0x3244
f2fs_ioctl+0x54/0xe0
__arm64_sys_ioctl+0xa8/0xe4
invoke_syscall+0x58/0x114
checkpoint and f2fs_remount may race as below, resulting triggering warning
in dquot_writeback_dquots().
atomic write remount
- do_remount
- down_write(&sb->s_umount);
- f2fs_remount
- ioctl
- f2fs_do_sync_file
- f2fs_sync_fs
- f2fs_write_checkpoint
- block_operations
- locked = down_read_trylock(&sbi->sb->s_umount)
: fail to lock due to the write lock was held by remount
- up_write(&sb->s_umount);
- f2fs_quota_sync
- dquot_writeback_dquots
- WARN_ON_ONCE(!rwsem_is_locked(&sb->s_umount))
: trigger warning because s_umount lock was unlocked by remount
If checkpoint comes from mount/umount/remount/freeze/quotactl, caller of
checkpoint has already held s_umount lock, calling dquot_writeback_dquots()
in the context should be safe.
So let's record task to sbi->umount_lock_holder, so that checkpoint can
know whether the lock has held in the context or not by checking current
w/ it.
In addition, in order to not misrepresent caller of checkpoint, we should
not allow to trigger async checkpoint for those callers: mount/umount/remount/
freeze/quotactl. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix block group refcount race in btrfs_create_pending_block_groups()
Block group creation is done in two phases, which results in a slightly
unintuitive property: a block group can be allocated/deallocated from
after btrfs_make_block_group() adds it to the space_info with
btrfs_add_bg_to_space_info(), but before creation is completely completed
in btrfs_create_pending_block_groups(). As a result, it is possible for a
block group to go unused and have 'btrfs_mark_bg_unused' called on it
concurrently with 'btrfs_create_pending_block_groups'. This causes a
number of issues, which were fixed with the block group flag
'BLOCK_GROUP_FLAG_NEW'.
However, this fix is not quite complete. Since it does not use the
unused_bg_lock, it is possible for the following race to occur:
btrfs_create_pending_block_groups btrfs_mark_bg_unused
if list_empty // false
list_del_init
clear_bit
else if (test_bit) // true
list_move_tail
And we get into the exact same broken ref count and invalid new_bgs
state for transaction cleanup that BLOCK_GROUP_FLAG_NEW was designed to
prevent.
The broken refcount aspect will result in a warning like:
[1272.943527] refcount_t: underflow; use-after-free.
[1272.943967] WARNING: CPU: 1 PID: 61 at lib/refcount.c:28 refcount_warn_saturate+0xba/0x110
[1272.944731] Modules linked in: btrfs virtio_net xor zstd_compress raid6_pq null_blk [last unloaded: btrfs]
[1272.945550] CPU: 1 UID: 0 PID: 61 Comm: kworker/u32:1 Kdump: loaded Tainted: G W 6.14.0-rc5+ #108
[1272.946368] Tainted: [W]=WARN
[1272.946585] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[1272.947273] Workqueue: btrfs_discard btrfs_discard_workfn [btrfs]
[1272.947788] RIP: 0010:refcount_warn_saturate+0xba/0x110
[1272.949532] RSP: 0018:ffffbf1200247df0 EFLAGS: 00010282
[1272.949901] RAX: 0000000000000000 RBX: ffffa14b00e3f800 RCX: 0000000000000000
[1272.950437] RDX: 0000000000000000 RSI: ffffbf1200247c78 RDI: 00000000ffffdfff
[1272.950986] RBP: ffffa14b00dc2860 R08: 00000000ffffdfff R09: ffffffff90526268
[1272.951512] R10: ffffffff904762c0 R11: 0000000063666572 R12: ffffa14b00dc28c0
[1272.952024] R13: 0000000000000000 R14: ffffa14b00dc2868 R15: 000001285dcd12c0
[1272.952850] FS: 0000000000000000(0000) GS:ffffa14d33c40000(0000) knlGS:0000000000000000
[1272.953458] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1272.953931] CR2: 00007f838cbda000 CR3: 000000010104e000 CR4: 00000000000006f0
[1272.954474] Call Trace:
[1272.954655] <TASK>
[1272.954812] ? refcount_warn_saturate+0xba/0x110
[1272.955173] ? __warn.cold+0x93/0xd7
[1272.955487] ? refcount_warn_saturate+0xba/0x110
[1272.955816] ? report_bug+0xe7/0x120
[1272.956103] ? handle_bug+0x53/0x90
[1272.956424] ? exc_invalid_op+0x13/0x60
[1272.956700] ? asm_exc_invalid_op+0x16/0x20
[1272.957011] ? refcount_warn_saturate+0xba/0x110
[1272.957399] btrfs_discard_cancel_work.cold+0x26/0x2b [btrfs]
[1272.957853] btrfs_put_block_group.cold+0x5d/0x8e [btrfs]
[1272.958289] btrfs_discard_workfn+0x194/0x380 [btrfs]
[1272.958729] process_one_work+0x130/0x290
[1272.959026] worker_thread+0x2ea/0x420
[1272.959335] ? __pfx_worker_thread+0x10/0x10
[1272.959644] kthread+0xd7/0x1c0
[1272.959872] ? __pfx_kthread+0x10/0x10
[1272.960172] ret_from_fork+0x30/0x50
[1272.960474] ? __pfx_kthread+0x10/0x10
[1272.960745] ret_from_fork_asm+0x1a/0x30
[1272.961035] </TASK>
[1272.961238] ---[ end trace 0000000000000000 ]---
Though we have seen them in the async discard workfn as well. It is
most likely to happen after a relocation finishes which cancels discard,
tears down the block group, etc.
Fix this fully by taking the lock arou
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix the recovery flow of the UMR QP
This patch addresses an issue in the recovery flow of the UMR QP,
ensuring tasks do not get stuck, as highlighted by the call trace [1].
During recovery, before transitioning the QP to the RESET state, the
software must wait for all outstanding WRs to complete.
Failing to do so can cause the firmware to skip sending some flushed
CQEs with errors and simply discard them upon the RESET, as per the IB
specification.
This race condition can result in lost CQEs and tasks becoming stuck.
To resolve this, the patch sends a final WR which serves only as a
barrier before moving the QP state to RESET.
Once a CQE is received for that final WR, it guarantees that no
outstanding WRs remain, making it safe to transition the QP to RESET and
subsequently back to RTS, restoring proper functionality.
Note:
For the barrier WR, we simply reuse the failed and ready WR.
Since the QP is in an error state, it will only receive
IB_WC_WR_FLUSH_ERR. However, as it serves only as a barrier we don't
care about its status.
[1]
INFO: task rdma_resource_l:1922 blocked for more than 120 seconds.
Tainted: G W 6.12.0-rc7+ #1626
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:rdma_resource_l state:D stack:0 pid:1922 tgid:1922 ppid:1369
flags:0x00004004
Call Trace:
<TASK>
__schedule+0x420/0xd30
schedule+0x47/0x130
schedule_timeout+0x280/0x300
? mark_held_locks+0x48/0x80
? lockdep_hardirqs_on_prepare+0xe5/0x1a0
wait_for_completion+0x75/0x130
mlx5r_umr_post_send_wait+0x3c2/0x5b0 [mlx5_ib]
? __pfx_mlx5r_umr_done+0x10/0x10 [mlx5_ib]
mlx5r_umr_revoke_mr+0x93/0xc0 [mlx5_ib]
__mlx5_ib_dereg_mr+0x299/0x520 [mlx5_ib]
? _raw_spin_unlock_irq+0x24/0x40
? wait_for_completion+0xfe/0x130
? rdma_restrack_put+0x63/0xe0 [ib_core]
ib_dereg_mr_user+0x5f/0x120 [ib_core]
? lock_release+0xc6/0x280
destroy_hw_idr_uobject+0x1d/0x60 [ib_uverbs]
uverbs_destroy_uobject+0x58/0x1d0 [ib_uverbs]
uobj_destroy+0x3f/0x70 [ib_uverbs]
ib_uverbs_cmd_verbs+0x3e4/0xbb0 [ib_uverbs]
? __pfx_uverbs_destroy_def_handler+0x10/0x10 [ib_uverbs]
? __lock_acquire+0x64e/0x2080
? mark_held_locks+0x48/0x80
? find_held_lock+0x2d/0xa0
? lock_acquire+0xc1/0x2f0
? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs]
? __fget_files+0xc3/0x1b0
ib_uverbs_ioctl+0xe7/0x170 [ib_uverbs]
? ib_uverbs_ioctl+0xcb/0x170 [ib_uverbs]
__x64_sys_ioctl+0x1b0/0xa70
do_syscall_64+0x6b/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f99c918b17b
RSP: 002b:00007ffc766d0468 EFLAGS: 00000246 ORIG_RAX:
0000000000000010
RAX: ffffffffffffffda RBX: 00007ffc766d0578 RCX:
00007f99c918b17b
RDX: 00007ffc766d0560 RSI: 00000000c0181b01 RDI:
0000000000000003
RBP: 00007ffc766d0540 R08: 00007f99c8f99010 R09:
000000000000bd7e
R10: 00007f99c94c1c70 R11: 0000000000000246 R12:
00007ffc766d0530
R13: 000000000000001c R14: 0000000040246a80 R15:
0000000000000000
</TASK> |
