| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix percpu map update indexing with sparse CPU IDs
Per-CPU array, hash, and cgroup storage map updates without BPF_F_CPU
or BPF_F_ALL_CPUS use a value buffer whose per-CPU slots are packed in
possible-CPU order. The buffer is sized as:
round_up(value_size, 8) * num_possible_cpus()
The update paths iterate over possible CPUs, but use the logical CPU ID
to calculate the source offset:
value + size * cpu
This only works when possible CPU IDs are contiguous starting at zero.
For example, with a possible CPU mask of 0,2-3, the buffer contains
three slots corresponding to CPUs 0, 2, and 3. CPU2 is therefore
expected to use slot 1 and CPU3 slot 2. Instead, the current code uses
slots 2 and 3 respectively, causing incorrect per-CPU values and an
out-of-bounds read from the update buffer for CPU3.
The corresponding lookup paths already use a dense offset while
iterating over possible CPUs. Do the same for the array, hash, and
cgroup storage update paths, advancing the source offset once for each
possible CPU. BPF_F_ALL_CPUS continues to use the same value for every
CPU. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix REG INVARIANTS VIOLATION on speculative pointer arithmetic
Take the following unprivileged program as an example:
r0 = bpf_map_lookup_elem(...) /* PTR_TO_MAP_VALUE, offset 0 */
...
14: r0 += r1 /* r1 is a bounded scalar */
15: r9 = r0
Loading it triggers a verifier warning from reg_bounds_sanity_check():
verifier bug: REG INVARIANTS VIOLATION (alu): const subreg tnum out
of sync with range bounds r64={.base=0x0, .size=0x0}
r32={.base=0x0, .size=0xffffffff} var_off=(0x0, 0x0)
What happens:
1. Processing insn 14 (r0 += r1) in adjust_ptr_min_max_vals(), the new
offset is computed into dst_reg's var_off and 32/64-bit ranges.
2. Because pointer registers do not track 32-bit subregister bounds,
__mark_reg32_unbounded() first sets r32 to the full range; r32 is
re-derived from the offset at the end of the function by
reg_bounds_sync().
3. On the unprivileged path, sanitize_ptr_alu() is called and, via
sanitize_speculative_path() -> push_stack(), snapshots the current
register state and schedules the next instruction (insn 15) to be
verified directly as a speculative path.
4. That snapshot is taken between step 2 and the final reg_bounds_sync():
at this point dst_reg's var_off still holds the (const) original
offset while r32 has just been blanked to the full range, i.e. the two
are out of sync. When the speculative path later verifies insn 15
(r9 = r0), the inconsistent state reaches reg_bounds_sanity_check() and
trips the warning.
var_off and the 32-bit range must always be consistent. There are two
ways to keep the snapshot consistent:
1. sync var_off and r32 before the snapshot so they match, or
2. leave r32 at its original (already consistent) value and blank it
only after the snapshot.
The whole point of sanitize_ptr_alu() is to insert a harmless masking
sequence that keeps the access in bounds under speculation, so the state
it snapshots should faithfully represent that. Take approach 2: move
__mark_reg32_unbounded() to after sanitize_ptr_alu(), so the speculative
snapshot keeps the pointer's original, consistent r32. The non-speculative
path is unchanged: r32 is still blanked before the offset is applied and
re-derived by reg_bounds_sync(). |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: fix racy access to FDP placement id array
nvme_query_fdp_info() is called per-path and therefore prone to races.
It populates head->nr_plids/head->plids for fdp registration.
But nothing protects that pair from concurrent access - two paths scanning
the same namespace can race to populate it.
Avoid the race by moving this initialization work to nvme_alloc_ns_head()
which is called once per shared namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: platform: Use acpi_bus_get_primary_device()
The acpi_get_first_physical_node() usage in acpi_platform_fill_resource()
and acpi_create_platform_device() is generally unsafe because in theory
the device returned by it may be freed at any time [1].
It is also inefficient because acpi_get_first_physical_node() is called
multiple times for the same argument which can be avoided.
Address these issues by using acpi_bus_get_primary_device() instead of
acpi_get_first_physical_node() and adjusting the code to call it just
once at the beginning of and acpi_create_platform_device() and drop
the device reference acquired by it upon the return from that function. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hsr: free learned nodes on device setup failure
hsr_dev_finalize() can fail after a lower-device RX handler has
already been registered (slave A is added before the failable slave B
and interlink adds). RX handlers run in softirq regardless of the
master's state, so frames received in that window can learn dynamic
nodes into node_db, and the error unwind never releases them.
Free both owned dynamic databases in the unwind, mirroring
hsr_dellink(). proxy_node_db is provably empty on every current error
exit (only interlink RX feeds it, and the interlink add is the last
failable step) and is freed for symmetry. The order is safe:
hsr_del_port() unregisters each RX handler with synchronize_net()
before hsr_del_nodes() runs, which removes remaining entries with
list_del_rcu() and defers their release with call_rcu() for readers
already under RCU. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize SCO and ISO scheduling with teardown
hci_low_sent() selects a connection under RCU but drops the read lock
before calculating its quota and returning it to the scheduler. The
connection is then used without lifetime protection by hci_sched_iso()
and hci_sched_sco().
After the TX worker drops the RCU read lock, hci_abort_conn_sync() on
hdev->req_workqueue can remove the connection from the hash, complete
synchronize_rcu(), purge its queues and release it. The TX worker on
hdev->workqueue can then access the freed connection in hci_quote_sent()
or while dequeuing packets and updating conn->sent.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_low_sent+0x730/0x840
Workqueue: hci0 hci_tx_work
Call Trace:
hci_low_sent+0x730/0x840
hci_sched_iso+0x25e/0x4d0
hci_tx_work+0x239/0xcb0
Allocated by task 93:
__hci_conn_add+0x16f/0x1b40
hci_bind_bis+0x782/0x17b0
hci_connect_bis+0xa0/0x510
iso_sock_connect+0x589/0x1050
Freed by task 88:
kfree+0x131/0x3c0
device_release+0xc8/0x240
kobject_put+0x14d/0x280
hci_conn_del+0x55a/0xe80
hci_disconnect_sync+0x156/0x180
hci_abort_conn_sync+0x3e7/0x940
hci_cmd_sync_work+0x13c/0x290
Hold hci_dev_lock() across connection selection and transmission in both
SCO and ISO scheduling, serializing them with connection teardown. This
also prevents queuing completion timestamps after the connection queues
have been purged. Extending RCU across transmission would be unsafe
because the transmit path can sleep. Keep the ISO timeout check outside
the mutex since hci_link_tx_to() takes it itself.
The preceding channel fix already holds this mutex in the ACL and LE
schedulers, which call the SCO scheduler between packets. Move the SCO
body to __hci_sched_sco(), assert that its caller holds the mutex, and
use it directly from these locked paths. Keep a locking hci_sched_sco()
wrapper for the direct calls from hci_tx_work(). This avoids recursively
acquiring the device mutex while preserving the scheduling order.
Remove the obsolete claim that connection removal disables TX. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Bail from shadow walks if the root is invalid or a dummy
When walking shadow page tables, immediately terminate the walk if the root
is a "dummy" root, i.e. a root whose top-level page table is backed by the
zero page, but otherwise doesn't exist. If memslot creation races with a
stage-2 page fault (EPT violation or #NPF) from L2, then if the stars align,
KVM will attempt to walk shadow page tables using the zero page and hit a
NULL pointer deref.
BUG: kernel NULL pointer dereference, address: 0000000000000021
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP
CPU: 30 UID: 1000 PID: 941 Comm: qemu Not tainted 7.2.0-rc2-1b731e5ded48-next-vm #1741 PREEMPTLAZY
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:__kvm_mmu_invalidate_addr+0xea/0x210 [kvm]
Call Trace:
<TASK>
kvm_mmu_invalidate_addr+0x92/0xe0 [kvm]
__kvm_inject_emulated_page_fault+0x67/0x80 [kvm]
ept_page_fault+0x160/0x850 [kvm]
kvm_mmu_do_page_fault+0x102/0x1f0 [kvm]
kvm_mmu_page_fault+0x8e/0x6b0 [kvm]
vmx_handle_exit+0x163/0x640 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x960/0x2120 [kvm]
kvm_vcpu_ioctl+0x2c7/0x970 [kvm]
__x64_sys_ioctl+0x90/0xd0
do_syscall_64+0x67/0x5f0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f606d0b53bb
Opportunistically harden the shadow walks against fully invalid roots, but
WARN, as all callers are expected/required to pre-check for a valid root.
Don't WARN in the dummy root case as the whole point of using a dummy root
is to provide a root that's valid enough to enter the guest, i.e. it should
Just Work for all flows except those that *need* to know about dummy roots.
Alternatively, KVM could allocate a dedicated page and associated shadow
page structure for the dummy root, which is very tempting as it such an
approach should be more resilient against unexpected behavior. But that
would be a much larger and thus riskier change than simply terminating
walks of dummy roots. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Use the active VMCB's MSR bitmap when checking if MSR is intercepted
Use the MSR permission bitmap of the active VMCB instead of assuming that
KVM is always using vmcb02's bitmap when L2 is active, as KVM uses msrpm02
if and only if L1 wants to intercept MSR accesses, i.e. if and only if KVM
needs to merge msprm01 with msrpm12.
Don't bother tracking the virtual address of the bitmap that's being used,
as __va() is cheap on x86, and caching the virtual address would introduce
yet another source of potentially stale information. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlegacy: 3945: free EEPROM data on remove
il3945_pci_probe() calls il_eeprom_init(), which allocates memory for
the EEPROM data. The probe failure paths release this allocation with
il_eeprom_free(), but the remove path does not free it after a
successful probe.
As a result, the EEPROM data is leaked when the PCI device is removed.
Free the EEPROM data in il3945_pci_remove() before releasing the
mac80211 hardware structure.
This issue was found by manual code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: count only matching reservations in reserved switch
ieee80211_vif_use_reserved_switch() validates a replacement by counting
assigned links on ctx->replace_ctx and treating reservations too
broadly. A link can still be assigned to the old channel context while
holding a reservation that belongs to a different replacement
operation.
That can make the current replacement appear complete too early. If
another link finalizes first, the function can free the
WILL_BE_REPLACED chanctx while the unmatched link and driver still use
it, leading to a use-after-free in later beacon generation.
Require an in-place reservation to point at the current replacement
context, and require the reserved and assigned contexts to be the
matching replacement pair, before counting or moving the link. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix mesh fast xmit path deletion UAF
mesh_fast_tx_cache() stores raw mesh_path pointers. Path deletion
flushes the cache and then frees the path with kfree_rcu(), but a
lookup that already holds the path can insert a new cache entry
after the flush. The cache then points at freed memory.
Set MESH_PATH_DELETED before flushing, and skip inserting a cache
entry if the path or MPP path is already deleted. Check this under
the cache walk lock so it is ordered with the flush. Use WRITE_ONCE()
for the deletion flag updates because the cache check reads flags
without taking state_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: handle empty FILS association request payload
fils_encrypt_assoc_req() accepts a (Re)Association Request frame whose
last element is the FILS Session element. crypt_len is then zero and
aes_siv_encrypt() is called with an empty plaintext.
kmemdup() returns ZERO_SIZE_PTR for a zero-length allocation, so the
unconditional sg_init_one() puts an invalid page into the scatterlist.
With CONFIG_DEBUG_SG this triggers a kernel BUG in sg_set_buf();
without the debug check the bogus page is handed to the crypto backend.
AES-SIV is defined for empty plaintext and the S2V result is then the
complete output, so handle this case before the CTR step, which has
nothing to encrypt. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix ioctl hangup race
The tty ioctls can race with hangup and end up calling into a tty driver
for a device that is already gone or powered down.
Serialise the callbacks using the tty port mutex and add the missing
checks to make sure the port has not been hung up before accessing port
driver data or hardware.
This specifically avoids dereferencing a NULL-pointer if a device is
disconnected during lengthy break signalling.
Note that TIOCGICOUNT and TIOCMIWAIT do not access port driver data or
hardware and are therefore not affected by the race. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix KASAN reported use-after-free when request is canceled
Alan reported that when doing stress testing sometimes KASAN notices
use-after-free during control channel operation (stripped down keeping
the relevant parts):
BUG: KASAN: slab-use-after-free in tb_cfg_request_sync+0x240/0x250 [thunderbolt]
Read of size 24 at addr ffff88811067f290 by task kworker/u40:2/1760
<TASK>
tb_cfg_request_sync+0x240/0x250 [thunderbolt]
tb_cfg_read_raw+0x367/0x510 [thunderbolt]
tb_cfg_read+0xec/0x240 [thunderbolt]
tb_port_get_link_generation+0x258/0x420 [thunderbolt]
tb_usb3_consumed_bandwidth+0x1c1/0x2c0 [thunderbolt]
tb_tunnel_consumed_bandwidth+0xfd/0x910 [thunderbolt]
tb_available_bandwidth+0x5f2/0xeb0 [thunderbolt]
tb_recalc_estimated_bandwidth+0x2a0/0x1bc0 [thunderbolt]
tb_handle_dp_bandwidth_request+0x1897/0x5e20 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 1760:
__kmalloc_cache_noprof+0x1ee/0x550
tb_cfg_read_raw+0x1d3/0x510 [thunderbolt]
tb_cfg_read+0xec/0x240 [thunderbolt]
tb_port_get_link_generation+0x258/0x420 [thunderbolt]
tb_usb3_consumed_bandwidth+0x1c1/0x2c0 [thunderbolt]
tb_tunnel_consumed_bandwidth+0xfd/0x910 [thunderbolt]
tb_available_bandwidth+0x5f2/0xeb0 [thunderbolt]
tb_recalc_estimated_bandwidth+0x2a0/0x1bc0 [thunderbolt]
tb_handle_dp_bandwidth_request+0x1897/0x5e20 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
Freed by task 926:
kfree+0x18f/0x4a0
tb_cfg_request_put+0xb7/0xe0 [thunderbolt]
tb_cfg_request_work+0x82/0x120 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
Second to last potentially related work creation:
__queue_work+0x575/0xd00
queue_work_on+0x77/0x80
tb_cfg_request_cancel+0xc7/0x260 [thunderbolt]
tb_cfg_request_sync+0x1f6/0x250 [thunderbolt]
tb_cfg_read_raw+0x367/0x510 [thunderbolt]
tb_cfg_read+0xec/0x240 [thunderbolt]
tb_port_get_link_generation+0x258/0x420 [thunderbolt]
tb_usb3_consumed_bandwidth+0x1c1/0x2c0 [thunderbolt]
tb_tunnel_consumed_bandwidth+0xfd/0x910 [thunderbolt]
tb_available_bandwidth+0x5f2/0xeb0 [thunderbolt]
tb_recalc_estimated_bandwidth+0x2a0/0x1bc0 [thunderbolt]
tb_handle_dp_bandwidth_request+0x1897/0x5e20 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
The last stack trace is helpful because it shows that we are cancelling
a request and looking at tb_cfg_request_cancel() what might happen is
that tb_cfg_request_work() completes right before tb_cfg_request_cancel()
starts and because of this it will call schedule_work() queueing the
same work to run again. However, it is already removed from the
request_queue and reference count is dropped so when
tb_cfg_request_work() triggers again it will access memory that is
already released.
Fix this so that we first make sure a cancelled request is not handed
away from tb_cfg_request_find() or scheduled to run. Then instead of
relying on the worker to clean up the request we will do it in
tb_cfg_request_cancel() after the work is canceled from running. Make
tb_cfg_request_dequeue() release the request only if it was actually
removed from the queue. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: stm32-adc: fix possible division by zero in processed channel
In case the conversion has failed or returned zero, processing *val
can lead to a division by zero. Need to check for errors, or converted
value is zero, before processing the data. In case the converted value
is zero, e.g. the Vrefint channel, this should be considered as invalid
in all cases. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: sun4i-gpadc-iio: clean up on thermal zone registration failure
If devm_thermal_of_zone_register() fails, probe returns without
unregistering the IIO map array or disabling runtime PM.
Jump to err_map to release them. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: xilinx-xadc: free IRQ before cancelling the unmask worker on unbind
The ZYNQ XADC alarm IRQ handler queues zynq_unmask_work via
schedule_delayed_work(); that work is cleared by a devm callback.
Register the devm callback before devm_request_irq() so the devres LIFO
teardown frees the IRQ first, ensuring the handler can no longer queue
work by the time the workqueue is cleared. Otherwise the handler could
re-arm the work and run it after the xadc structure has been freed.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: Ensure bounce buffer used for unaligned case is zeroed.
iio_push_to_buffers_with_ts_unaligned() leaks uninitialized heap memory
to userspace if the data passed in is not a multiple of 8 bytes and the
timestamp is enabled. Specify __GFP_ZERO for the devm_krealloc()
to ensure any extra space is cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: health: max30102: fix NULL dereference in interrupt handler
The interrupt is requested in max30102_probe() and stays enabled
for the lifetime of the device, but indio_dev->active_scan_mask is only
valid while a buffer is enabled. When an interrupt arrives while no
buffer is enabled, the handler dereferences the NULL active_scan_mask:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
__bitmap_weight+0x64/0x98 (P)
max30102_interrupt_handler+0x48/0x160 [max30102]
Call max30102_fifo_count() at the top of the handler and return early
unless it reports a FIFO sample is ready. Because FIFO_RDY is the only
interrupt source enabled in max30102_chip_init(), an invocation of
max30102_interrupt_handler() without the FIFO_RDY interrupt status bit
set carries no data to read and can return before touching
active_scan_mask. A negative return from max30102_fifo_count()
indicates a failed interrupt status read and is treated the same way. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: pressure: bmp280: fix out-of-bounds access in sampling frequency lookup
The sampling frequency tables store each frequency as an integer part and
a fractional part in micro units. num_sampling_freq_avail is initialized
to the number of flattened integer elements because read_avail() returns
the table as a flat array.
bmp280_write_sampling_frequency(), however, indexes the same table as a
two-dimensional array and uses num_sampling_freq_avail as the number of
rows. Convert the flattened element count back to the number of rows
before iterating over the table. |
