| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
llc: reserve device headroom for allocated frames
llc_alloc_frame() reserves link-layer headroom using the device type.
This is insufficient for stacked Ethernet devices such as VLAN devices,
where vlan_dev_hard_header() pushes a VLAN header before the lower
device's Ethernet header. An LLC response on such a device can
therefore underflow skb headroom in eth_header().
Use LL_RESERVED_SPACE() to account for the device's actual required
headroom while preserving the existing LLC device-type check. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: cdev: fix kernel stack leak to user-space in error path
If we fail to acquire the GPIO chip guard in gpio_desc_to_lineinfo(), we
return immediately before zeroing the info struct we'll end up passing
to the user-space later in lineinfo_get_v1(). This may leak the kernel
stack contents. Make gpio_desc_to_lineinfo() return int so that the
-ENODEV returned on failure to acquire the guard can be propagated to
the callers.
While not strictly necessary: move the memset() before trying to acquire
the SRCU read lock too for good measure. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/server: cancel async requests when closing connection
An async request may still be waiting when a connection is closed.
This can stop the connection from closing.
Cancel active async requests before waiting for them to finish. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't let hidden_space go negative in xfs_metafile_resv_init
LOLLM points out that if the amount of fdblocks that we can reserve for
a metadata btree file goes below the space already used by that file,
then the hidden_space subtraction can underflow, causing
xfs_dec_fdblocks to subtract a huge amount of space. We never want the
target to be less than the used sapce, so fix the logic that adjusts
dblocks_avail downwards.
Also fix an error in the adjacent comment. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: arizona: Fix runtime PM leak in arizona_gpio_direction_out()
Switching a persistent GPIO line from input to output acquires a
runtime PM reference on the parent device, but if the subsequent
regmap_update_bits() fails the reference is never dropped and no later
direction_in() can balance it since the direction was never changed.
Drop the reference on the update failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
kprobes: Fix permanent hang when flushing the kprobe optimizer
Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is
jump-optimized never returns. The writer sleeps in D state forever with
kprobe_sysctl_mutex held, so any later read or write of that sysctl
hangs as well. For example, with vfs_read+9 as an optimizable address
in this build:
# cd /sys/kernel/tracing
# echo 'p:myprobe vfs_read+9' >> kprobe_events
# echo 1 > events/kprobes/myprobe/enable
# # wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED]
# echo 0 > /proc/sys/debug/kprobes-optimization
INFO: task sh:246 blocked for more than 10 seconds.
Call Trace:
<TASK>
__schedule+0x1176/0x4f70
schedule+0xdc/0x2c0
schedule_timeout+0x17b/0x260
wait_for_completion+0x173/0x3c0
wait_for_kprobe_optimizer_locked+0xbc/0x130
proc_kprobes_optimization_handler+0x156/0x1b0
proc_sys_call_handler+0x324/0x490
vfs_write+0x52d/0xfe0
ksys_write+0xff/0x200
do_syscall_64+0x106/0x630
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
...
INFO: task cat:265 is blocked on a mutex likely owned by task sh:246.
wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion,
asks the optimizer thread to flush and sleeps in wait_for_completion().
The thread drains the (un)optimizing lists, but calls complete() only
if completion_done() is true, i.e. if the completion is already done,
which never happens while someone waits. disarm_all_kprobes() and
kprobe_trace_self_tests_init() wait the same way.
Calling complete() unconditionally would not be enough: the waiter
drops kprobe_mutex while it sleeps, and nothing else serializes the
sysctl handler against the debugfs "enabled" file. A second flusher
that still finds the lists non-empty, e.g. because a disabled probe is
queued for unoptimizing, reinitializes the completion under the first:
sysctl write debugfs "enabled" write
unoptimize_all_kprobes()
wait_for_kprobe_optimizer_locked()
init_completion(c)
mutex_unlock(&kprobe_mutex)
wait_for_completion(c)
disarm_all_kprobes()
wait_for_kprobe_optimizer_locked()
init_completion(c)
// c->wait is reset, the first
// waiter is off the queue
mutex_unlock(&kprobe_mutex)
wait_for_completion(c)
kprobe_optimizer()
complete(c)
// wakes the debugfs writer only
where c is &optimizer_completion. Lining up the two writes during an
optimizer pass loses the sysctl writer this way.
Replace the completion with a counter of optimizer passes, bumped at the
end of each pass and signalled with wake_up_var_locked(), both under
kprobe_mutex. A flusher samples the count and waits with
wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so
a new count means a whole pass ran in the meantime. Nothing is
reinitialized, so several flushers can sleep in the wait at once. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: sr: enforce exact attribute length for SEG6_ATTR_DST
In seg6_genl_policy, SEG6_ATTR_DST is defined with .type = NLA_BINARY and
.len = sizeof(struct in6_addr). For NLA_BINARY, .len only enforces the
maximum payload length and permits shorter payloads (e.g., 0 bytes).
When seg6_genl_set_tunsrc() copies sizeof(struct in6_addr) bytes via
kmemdup(val, sizeof(*val), GFP_KERNEL), a short SEG6_ATTR_DST attribute
triggers a 16-byte out-of-bounds read past skb->tail into uninitialized
skb->head memory, which is stored in sdata->tun_src and leaked back to
userspace via SEG6_CMD_GET_TUNSRC.
Switch SEG6_ATTR_DST in seg6_genl_policy to
NLA_POLICY_EXACT_LEN(sizeof(struct in6_addr)) so that generic netlink
validation rejects any attribute whose length is not exactly
sizeof(struct in6_addr) with -ERANGE.
Tested in QEMU against Linux 7.3.0-rc3 by sending a SEG6_CMD_SET_TUNSRC
Generic Netlink message with a 0-byte SEG6_ATTR_DST attribute followed
by SEG6_CMD_GET_TUNSRC. On the unfixed kernel, SEG6_CMD_SET_TUNSRC
succeeds (err = 0) and SEG6_CMD_GET_TUNSRC leaks 16 bytes of
uninitialized kernel heap memory (tun_src =
836a61ecc4d25a1042a8d60411cfb378); with this patch applied,
SEG6_CMD_SET_TUNSRC is rejected by netlink policy validation with
-ERANGE (-34) and tun_src remains zeroed. |
| In the Linux kernel, the following vulnerability has been resolved:
ipe: fix use-after-free when auditing a newly loaded policy
new_policy() audits the policy after ipe_new_policyfs_node() publishes it
and drops the new directory's inode lock. A concurrent delete can free
the policy while ipe_audit_policy_load() is still using it.
Audit the successful load under that lock.
[FW: remove model name according to latest guideline] |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: clean up failed cached directory opens
open_cached_dir() sends CREATE and QUERY_INFO as a compound request. If
the CREATE succeeds but a later command returns an error, the function
must retain the CREATE FID so common cleanup can issue SMB2_close(). It
also must not treat a response error as a valid CREATE.
Validate the CREATE response before using its fields, record the FIDs, and
mark the handle open before handling errors from later compound commands.
Move the -EREMCHG reconnect handling before response validation so a
missing response does not hide the reconnect request. Count the handle
when it is marked open; confirmed close responses decrement the counter,
while existing close retry behavior remains best effort on transport
failures. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: release unused CIS holds after channel attach
hci_bind_cis() and hci_connect_cis() return one hci_conn hold for the
ISO layer. A new channel association consumes that hold, which is
eventually released by iso_conn_free().
There are two cases where iso_chan_add() does not create an association:
it returns success when the socket is already attached to the same
iso_conn, and it returns -EBUSY when another socket is attached. The
hold returned for the current call is unused in both cases. This occurs
when deferred setup calls iso_connect_cis() again for its existing
socket, or when another socket attempts to reuse the CIS.
Detect the idempotent case while the connection is locked and release
the unused hold after iso_chan_add(). Also release it on -EBUSY. Do not
drop it for other errors: a newly allocated iso_conn releases the
transferred hold when its last temporary reference is put. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Transfer the hyp stack pages out of the host stage-2
fix_host_ownership() walks only the linear-map alias of each memblock
region, and the per-CPU hyp stack, mapped in the private VA range for
its guard page, has none.
Walk each stack's VA range with the same walker. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: flush dirty data before zeroing a range
smb3_zero_range() emulates FALLOC_FL_ZERO_RANGE by invalidating the
page cache over the target range with truncate_pagecache_range() and
then issuing FSCTL_SET_ZERO_DATA to the server.
Dirty data was only flushed conditionally, when the range reached or
extended EOF. For a purely interior zero range that does not reach
EOF, no flush happened, so a dirty folio overlapping the range could
be written back to the server after the FSCTL and refill the range
that was just zeroed with stale data.
Fix this by unconditionally flushing and waiting for dirty data in the
range before invalidating the page cache and issuing
FSCTL_SET_ZERO_DATA, exactly as was done for smb3_punch_hole() in
commit d7d2adcd022b ("smb/client: flush dirty data before punching a
hole"); the two paths are structurally identical here.
This is observed as generic/363 randomly reading stale data where a
zeroed range is expected against Windows Server. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: fix memory leak of fence event on execbuffer failure
virtio_gpu_execbuffer_ioctl() reserves a DRM event with
drm_event_reserve_init() when VIRTGPU_EXECBUF_RING_IDX selects a ring that
userspace has enabled polling for. virtio_gpu_init_submit() does this
before the BO handles, the command buffer, the syncobj arrays and the
in-fence are processed, so every later error path runs with the event
already pending, including plain argument validation failures such as an
invalid bo_handle or an in-syncobj that carries no fence.
On those paths, virtio_gpu_cleanup_submit() drops the out-fence without
cancelling the event. The fence is freed without ever having been emitted,
taking the only driver-side pointer to the event with it. Closing the DRM
file does not help. drm_events_release() unlinks pending events but
deliberately leaves the freeing to the driver's later drm_send_event(),
which never runs for an orphaned event, so the allocation is leaked
permanently.
Found when fuzzing the virtio driver with Syzkaller:
BUG: memory leak
unreferenced object 0xffff88802c176e80 (size 96):
comm "syz.1.367", pid 10561, jiffies 4294960122
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
c8 6e 17 2c 80 88 ff ff 00 00 00 00 00 00 00 00 .n.,............
backtrace (crc e1973c6b):
kmemleak_alloc_recursive include/linux/kmemleak.h:44 [inline]
slab_post_alloc_hook mm/slub.c:4597 [inline]
slab_alloc_node mm/slub.c:4917 [inline]
__kmalloc_cache_noprof+0x49d/0x6f0 mm/slub.c:5485
_kmalloc_noprof include/linux/slab.h:988 [inline]
_kzalloc_noprof include/linux/slab.h:1309 [inline]
virtio_gpu_fence_event_create drivers/gpu/drm/virtio/virtgpu_submit.c:282 [inline]
virtio_gpu_init_submit drivers/gpu/drm/virtio/virtgpu_submit.c:398 [inline]
virtio_gpu_execbuffer_ioctl+0xbbf/0x1aa0 drivers/gpu/drm/virtio/virtgpu_submit.c:505
drm_ioctl_kernel+0x1f4/0x3e0 drivers/gpu/drm/drm_ioctl.c:817
drm_ioctl+0x5f4/0xc70 drivers/gpu/drm/drm_ioctl.c:914
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x18e/0x210 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x116/0x800 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fix by cancelling and freeing the DRM event on the execbuffer error path
before dropping the fence. Clear the fence's event pointer after
cancellation so it does not retain a dangling pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: cn10k: restrict VF LMTLINE sharing to its own PF
rvu_mbox_handler_lmtst_tbl_setup() uses req->base_pcifunc as a direct
index into the LMT map table to read another function's LMTLINE
physical base address and copy it into the caller's own LMT map table
entry. The mailbox dispatcher authenticates req->hdr.pcifunc from the
IRQ source, but req->base_pcifunc is a separate payload field and is
not sanitized.
Reject the request with -EPERM when a VF caller's base_pcifunc is not a
valid function under its own PF. is_pf_func_valid() bounds the FUNC field
to the PF's configured VF count, keeping the computed index inside the
caller's own slot block. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_ct: preserve tc_skb_cb across defragmentation
tcf_ct_handle_fragments() calls nf_ct_handle_fragments() without saving
and restoring skb->cb. The defrag helper clears IPCB/IP6CB, which aliases
the tc_skb_cb/qdisc_skb_cb control buffer. Fragmented traffic through
act_ct therefore loses qdisc metadata such as pkt_segs and can trigger
WARN_ON_ONCE() in qdisc_pkt_segs() when panic_on_warn is enabled.
Save and restore the full tc_skb_cb around nf_ct_handle_fragments(),
matching the pattern used by ovs_ct_handle_fragments(). |
| In the Linux kernel, the following vulnerability has been resolved:
drop_monitor: fix size calculations for 64-bit attributes
net_dm_packet_report_fill() and net_dm_hw_packet_report_fill() use
nla_put_u64_64bit() to append 64-bit attributes (NET_DM_ATTR_PC and
NET_DM_ATTR_TIMESTAMP).
On 32-bit architectures without CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS,
nla_put_u64_64bit() may append a 4-byte NET_DM_ATTR_PAD attribute for
64-bit alignment.
However, net_dm_packet_report_size() and net_dm_hw_packet_report_size()
used nla_total_size(sizeof(u64)) instead of nla_total_size_64bit(sizeof(u64)),
budgeting 12 bytes instead of up to 16 bytes.
This under-estimation of SKB size can lead to an skb_over_panic() when
__nla_reserve() or skb_put() is subsequently called.
Fix this by using nla_total_size_64bit(sizeof(u64)) in both size calculations. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Clear __hyp_running_vcpu when flushing the pKVM hyp vCPU
flush_hyp_vcpu() copies the host vCPU context into the hyp's private
vCPU on every run. ctxt_to_vcpu() expects a guest context to have a
NULL __hyp_running_vcpu, which is only ever set on the host context, so
that it resolves the vCPU via container_of(). While this is generally
the case, flush_hyp_vcpu() copies the context verbatim and does not
enforce this, so a value provided by the host is dereferenced at EL2
(host -> EL2).
Fix by clearing __hyp_running_vcpu after the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: harden POSIX SID length parsing
posix_info_sid_size() reads sid[1] to obtain the subauthority count,
but its existing boundary check still accepts buffers with only one
remaining byte. Require two bytes before reading sid[1] so all client
paths that reuse the helper reject truncated POSIX SIDs safely. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6: vti: Use ip6_tnl.net in vti6_changelink().
ip netns add ns1
ip netns add ns2
ip -n ns1 link add vti6_test type vti6 remote ::1 local ::2 key 7
ip -n ns1 link set vti6_test netns ns2
ip -n ns2 link set vti6_test type vti6 remote ::3 local ::4 key 9
ip netns del ns2
ip netns del ns1
[ 132.495484] ------------[ cut here ]------------
[ 132.497609] kernel BUG at net/core/dev.c:12376!
Commit 61220ab34948 ("vti6: Enable namespace changing") dropped
NETIF_F_NETNS_LOCAL from vti6 devices. A vti6 tunnel can then
move through IFLA_NET_NS_FD. After the move dev_net(dev) points
at the new netns while t->net stays at the creation netns.
vti6_changelink() and vti6_update() still use dev_net(dev) and
dev_net(t->dev). They unlink from one per netns hash and relink
into another. The creation netns is left with a stale entry.
cleanup_net() of that netns later walks freed memory.
Reachable from an unprivileged user namespace (unshare --user
--map-root-user --net). Cross tenant scope on container hosts. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: 6lowpan: only accept IPv6 packets in lowpan_xmit()
The aoe driver (or similar) generates a non-IPv6 packet
(e.g., ETH_P_AOE) and queues it for transmission via dev_queue_xmit()
on a 6LoWPAN interface (configured by the user or test case).
Since the packet is not IPv6, the 6LoWPAN header_ops->create function
(lowpan_header_create or header_create) returns early without initializing
the lowpan_addr_info structure in the skb headroom.
In the transmit function (lowpan_xmit), the driver calls lowpan_header
(or setup_header) which unconditionally copies and uses the lowpan_addr_info
from the headroom, which contains uninitialized data.
Fix this by dropping non IPv6 packets.
A similar fix is needed in net/bluetooth/6lowpan.c bt_xmit(). |
