| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Validate CHAP_R length before base64 decode
chap_server_compute_hash() allocates client_digest as
kzalloc(chap->digest_size) and then, for BASE64-encoded responses,
passes chap_r directly to chap_base64_decode() without checking whether
the input length could produce more than digest_size bytes of output.
chap_base64_decode() writes to the destination unconditionally as long
as there is input to consume. With MAX_RESPONSE_LENGTH set to 128 and
the "0b" prefix stripped by extract_param(), up to 127 base64 characters
can reach the decoder. 127 characters decode to 95 bytes. For SHA-256
(digest_size=32) this overflows client_digest by 63 bytes; for MD5
(digest_size=16) the overflow is 79 bytes.
The length check at line 344 fires after the write has already happened.
The HEX branch in the same switch statement already validates the length
up front. Apply the same approach to the BASE64 branch: strip trailing
base64 padding characters, then reject any input whose data length
exceeds DIV_ROUND_UP(digest_size * 4, 3) before calling the decoder.
Stripping trailing '=' before the comparison handles both padded and
unpadded encodings. chap_base64_decode() already returns early on '=',
so the full original string is still passed to the decoder unchanged.
The mutual CHAP path decodes CHAP_C into initiatorchg_binhex, which is
kzalloc(CHAP_CHALLENGE_STR_LEN). extract_param() caps initiatorchg at
CHAP_CHALLENGE_STR_LEN characters, so at most CHAP_CHALLENGE_STR_LEN-1
base64 characters reach the decoder. The maximum decoded size,
DIV_ROUND_UP((CHAP_CHALLENGE_STR_LEN-1) * 3, 4), is less than
CHAP_CHALLENGE_STR_LEN, so no overflow is possible there. A comment is
added at the call site to document this. |
| Multiple Cisco products are affected by a vulnerability in the Snort 3 SMTP MIME Decoder that could allow an unauthenticated, remote attacker to cause the Snort 3 Detection Engine to restart.
This vulnerability is due to a lack of error checking when the MIME fields of the SMTP header are parsed. An attacker could exploit this vulnerability by sending crafted SMTP packets through an established connection to be parsed by Snort 3. A successful exploit could allow the attacker to cause a denial of service (DoS) condition when the Snort 3 Detection Engine unexpectedly restarts. |
| When NLnet Labs Unbound up to and including version 1.26.1 is configured with both a root trust anchor and an additional 'trust-anchor:' for an island-of-security zone whose parent is provably insecure under the root chain, a malicious actor who can deliver one forged NXDOMAIN response for a name inside the island, with the NSEC/SOA RRSIG 'SignerName' set to the insecure parent, tricks Unbound's validator to use the root trust anchor instead, and consecutively the insecure parent, thus causing that record to be treated as insecure and denying existence for records in the trust island. |
| Improper neutralization of Script-Related HTML tags in a web page (basic XSS) vulnerability in The Wikimedia Foundation MediaWiki Wikbase extension allows Cross-Site Scripting (XSS).
This issue affects MediaWiki Wikbase extension: 1.46, 1.45, and 1.43. |
| In `api-gateway` versions till `1.7.3`, The default rate-limit key resolver, `ClientIpKeyResolver`, derives the per-client bucket key from the leftmost element of the `X-Forwarded-For` request header. That element is supplied by the originating HTTP client and is not validated against any trusted-proxy list. A single attacker can therefore obtain an unlimited number of independent rate-limit buckets — one per unique header value — and completely bypass the gateway's request-rate limiting on every route that uses the shipped default configuration. |
| filelock is a platform-independent file lock for Python. From 3.22.0 until 4.2.1, SoftFileLock can trust a forged process identifier in a marker that an attacker can modify but cannot remove, allowing an authorized contender such as another process of the holder's account or root to act as a confused deputy, remove the live marker, and admit another holder. This issue is fixed in version 4.2.1. |
| The extension hides the correct answer to each CAPTCHA inside the image data of the CAPTCHA itself. Anyone who can request a CAPTCHA image can read the answer from it and submit it, so automated clients can pass the challenge. This applies to the default configuration, because the audio feature that causes the answer to be embedded is enabled by default. Forms that rely on the CAPTCHA as their only protection against automated submissions are exposed to abuse by bots. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate cookie AUTH state before use
When cookie authentication is disabled, COOKIE_ECHO restores fixed-size
AUTH fields directly from peer-controlled cookie bytes. A forged RANDOM
length, HMAC list, or CHUNKS list can then reach association consumers
with lengths or identifiers that were never validated against the local
backing arrays.
A forged RANDOM length can cause out-of-bounds reads during key-vector
construction. A forged HMAC identifier also caused a 32-byte write past
a zero-length AUTH chunk, providing a primitive for a local privilege
escalation chain.
Validate the cookie's RANDOM, HMACS, and CHUNKS parameters at the cookie
trust boundary before copying them into the association. Reject invalid
types, malformed lengths, unsupported HMAC identifiers, HMAC lists
without SHA1, and forbidden chunk ids. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Disable EOP for TPA on all chips to prevent data corruption
EOP (End of frame padding) on the AGG ring may cause overlapping of
zero padding at the end of one segment with the next segment's data.
If Relaxed Ordering (RO) is enabled, the zero padding may overwrite
valid data in the next segment and corrupt the data. Older chips
(P5 and older) do not automatically disable RO when EOP is enabled.
On some ARM systems, data corruption was reported on 57508 (P5)
chips with RO enabled.
Always disable EOP on all chips on the AGG rings when TPA is enabled
to fix the data corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Add a max slot check for SQ
The variable WQE mode must be validated against
the maximum slots supported by HW. The max supported
value is 64K. Adding a max and min check and fail if user
supplied value is more than the max supported and zero. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix zeropoint update where i_size > remote_i_size
Fix the update of the zero point[*] by netfs_release_folio() when there is
uncommitted data in the pagecache beyond the folio being released but the
on-server EOF is in this folio (ie. i_size > remote_i_size). The update
needs to limit zero_point to remote_i_size, not i_size as i_size is a local
phenomenon reflecting updates made locally to the pagecache, not stuff
written to the server. remote_i_size tracks the server's i_size.
[*] The zero point is the file position from which we can assume that the
server will just return zeros, so we can avoid generating reads.
Note that netfs_invalidate_folio() probably doesn't need fixing as
zero_point should be updated by setattr after truncation or fallocate.
Found with:
fsx -q -N 1000000 -p 10000 -o 128000 -l 600000 \
/xfstest.test/junk --replay-ops=junk.fsxops
using the following as junk.fsxops:
truncate 0x0 0x1bbae 0x82864
write 0x3ef2e 0xf9c8 0x1bbae
write 0x67e05 0xcb5a 0x4e8f6
mapread 0x57781 0x85b6 0x7495f
copy_range 0x5d3d 0x10329 0x54fac 0x7495f
write 0x64710 0x1c2b 0x7495f
mapread 0x64000 0x1000 0x7495f
on cifs with the default cache option.
It shows read-gaps on folio 0x64 failing with a short read (ie. it hits
EOF) if the FMODE_READ check is commented out in netfs_perform_write():
if (//(file->f_mode & FMODE_READ) ||
netfs_is_cache_enabled(ctx)) {
and no fscache. This was initially found with the generic/522 xfstest. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate embedded INIT chunk and address list lengths in cookie
sctp_unpack_cookie() only checked that the embedded INIT chunk length
did not exceed the remaining cookie payload, but did not ensure that the
INIT chunk is large enough to contain a complete INIT header.
A malformed COOKIE_ECHO can therefore carry a truncated INIT chunk whose
length field is smaller than sizeof(struct sctp_init_chunk). Later,
sctp_process_init() accesses INIT parameters unconditionally, which may
lead to out-of-bounds reads.
In addition, raw_addr_list_len is not fully validated against the
remaining cookie payload. When cookie authentication is disabled, an
attacker can supply an oversized raw_addr_list_len and cause
sctp_raw_to_bind_addrs() to read beyond the end of the cookie. The
address parser also lacks sufficient bounds checks for parameter headers
and lengths, allowing malformed address parameters to trigger
out-of-bounds reads.
Fix this by:
- requiring the embedded INIT chunk length to be at least sizeof(struct
sctp_init_chunk);
- validating that the INIT chunk and raw address list together fit
within the cookie payload;
- verifying sufficient data exists for each address parameter header and
payload before parsing it.
Note that sctp_verify_init() must be called after sctp_unpack_cookie()
and before sctp_process_init() when cookie authentication is disabled.
This will be addressed in a separate patch. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix oops when split header is enabled
For GMAC4, when split header is enabled, in some rare cases, the
hardware does not fill buf2 of the first descriptor with payload.
Thus we cannot assume buf2 is always fully filled if it is not
the last descriptor. Otherwise, the length of buf2 of the second
descriptor will be calculated wrong and cause an oops:
Unable to handle kernel paging request at virtual address ffff00019246bfc0
...
x2 : 0000000000000040 x1 : ffff00019246bfc0 x0 : ffff00009246c000
Call trace:
dcache_inval_poc+0x28/0x58 (P)
dma_direct_sync_single_for_cpu+0x38/0x6c
__dma_sync_single_for_cpu+0x34/0x6c
stmmac_napi_poll_rx+0x8f0/0xb60
__napi_poll.constprop.0+0x30/0x144
net_rx_action+0x160/0x274
handle_softirqs+0x1b8/0x1fc
...
To fix this, the PL bit-field in RDES3 register is used for all
descriptors, whether it is the last descriptor or not. |
| In the Linux kernel, the following vulnerability has been resolved:
zram: fix out-of-bounds access in read_block_state()
read_block_state() calculates nr_pages before taking dev_lock. If the
device is reset and reinitialized with a smaller disksize before lock
acquisition, nr_pages still describes the old table. The subsequent loop
can then call slot_lock() past the end of the newly allocated table.
Read disksize after acquiring dev_lock and checking that the device is
initialized. The read lock then keeps the table and its bound stable for
the duration of the scan. |
| In the Linux kernel, the following vulnerability has been resolved:
iavf: fix out-of-bounds writes in iavf_get_ethtool_stats()
iavf incorrectly uses real_num_tx_queues for ETH_SS_STATS. Since the
value could change in runtime, we should use num_tx_queues instead.
Moreover iavf_get_ethtool_stats() uses num_active_queues while
iavf_get_sset_count() and iavf_get_stat_strings() use
real_num_tx_queues, which triggers out-of-bounds writes when we do
"ethtool -L" and "ethtool -S" simultaneously [1].
For example when we change channels from 1 to 8, Thread 3 could be
scheduled before Thread 2, and out-of-bounds writes could be triggered
in Thread 3:
Thread 1 (ethtool -L) Thread 2 (work) Thread 3 (ethtool -S)
iavf_set_channels()
...
iavf_alloc_queues()
-> num_active_queues = 8
iavf_schedule_finish_config()
iavf_get_sset_count()
real_num_tx_queues: 1
-> buffer for 1 queue
iavf_get_ethtool_stats()
num_active_queues: 8
-> out-of-bounds!
iavf_finish_config()
-> real_num_tx_queues = 8
Use immutable num_tx_queues in all related functions to avoid the issue.
[1]
BUG: KASAN: vmalloc-out-of-bounds in iavf_add_one_ethtool_stat+0x200/0x270
Write of size 8 at addr ffffc900031c9080 by task ethtool/5800
CPU: 1 UID: 0 PID: 5800 Comm: ethtool Not tainted 6.19.0-enjuk-08403-g8137e3db7f1c #241 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
print_report+0x170/0x4f3
kasan_report+0xe1/0x180
iavf_add_one_ethtool_stat+0x200/0x270
iavf_get_ethtool_stats+0x14c/0x2e0
__dev_ethtool+0x3d0c/0x5830
dev_ethtool+0x12d/0x270
dev_ioctl+0x53c/0xe30
sock_do_ioctl+0x1a9/0x270
sock_ioctl+0x3d4/0x5e0
__x64_sys_ioctl+0x137/0x1c0
do_syscall_64+0xf3/0x690
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f7da0e6e36d
...
</TASK>
The buggy address belongs to a 1-page vmalloc region starting at 0xffffc900031c9000 allocated at __dev_ethtool+0x3cc9/0x5830
The buggy address belongs to the physical page: page: refcount:1 mapcount:0 mapping:0000000000000000
index:0xffff88813a013de0 pfn:0x13a013
flags: 0x200000000000000(node=0|zone=2)
raw: 0200000000000000 0000000000000000 dead000000000122 0000000000000000
raw: ffff88813a013de0 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffc900031c8f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc900031c9000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffffc900031c9080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
^
ffffc900031c9100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc900031c9180: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 |
| Vyper before 0.2.9 deploys forwarder proxies through the built-in create_forwarder_to function that report a fixed 4096-byte RETURNDATASIZE rather than the actual return data size. Calls through these proxies can yield corrupted data when a function returns more than 4096 bytes without return data sanitation, and fail strict return-size checks such as SafeERC20.safeTransfer. |
| Vite is a frontend tooling framework for JavaScript. Prior to 6.4.4, 7.3.7, 8.1.6, 8.2.4, and 8.3.3, applications using custom middleware are vulnerable when they pass an unchanged browser request URL to server.transformIndexHtml. getHtmlFilename uses the query-bearing request URL to resolve an existing local file while preserving attacker-supplied leading slashes in the generated proxy module URL. If the transformed HTML contains an inline module script and a victim browser loads the crafted development-server page, the leading double slash makes the browser fetch and execute an attacker-controlled module in the Vite-served page. This execution can expose sensitive page data or permit critical actions available to the affected application. This issue is fixed in versions 6.4.4, 7.3.7, 8.1.6, 8.2.4, and 8.3.3. |
| In Progress® Kendo® UI for jQuery versions starting with 2022.3.1109 and prior to 2026.3.1015, ToolBar ButtonGroup button URLs are concatenated into an unquoted href attribute after URL sanitization. An attacker who can control a button URL can supply an otherwise allowed HTTPS URL containing whitespace and additional attributes, including an event handler, and execute JavaScript in a user's browser when the affected button is interacted with. Successful exploitation can compromise the confidentiality and integrity of data accessible to the affected application. This issue is fixed in version 2026.3.1015. |
| In Progress® Kendo® UI for jQuery releases starting with v2020.1.114 and prior to 2026.3.1015, the Badge text method renders string values as raw HTML without encoding, including values supplied through text binding. An attacker who can modify data bound to a Badge can supply HTML containing event handlers that execute JavaScript in a user's browser when the Badge renders the value. Successful exploitation can compromise the confidentiality and integrity of data accessible to the affected application. This issue is fixed in version 2026.3.1015. |
| In Progress® Kendo® UI for jQuery versions starting with 2023.3.1010 and prior to 2026.3.1015, the FileManager component renders remotely supplied item names as HTML in its default drag hint even though the corresponding list items are encoded. An attacker who can control an item name can inject HTML containing event handlers that execute JavaScript in a user's browser when the user drags the affected item. Successful exploitation can compromise the confidentiality and integrity of data accessible to the affected application. This issue is fixed in version 2026.3.1015. |
